A low odor, easy clean-up, water based primer for adhering acrylic coatings such as Elasto-Tex™ Deck and Wall Coatings, as well as caulk, to concrete surfaces.
TECH DATA SHEET | APPLICATION GUIDE
AVAILABLE COLOR:

APPLICATION:
All surfaces must be clean, sound, and dry. For best results, the surface that has been coated with ELASTO-TEX™ PRIMER should be allowed to cure a minimum of 1 hour before being coated or caulked over. If for some reason primer is allowed to cure in excess of 24 hours, the surface should be reprimed with ELASTO-TEX™ PRIMER before coating over with the ELASTO-TEX™ system. Recommended coverage is approximately 250 sq.ft. per gallon on rough surfaces to 350 sq.ft. per gallon on smooth surfaces. Tools and equipment should be cleaned immediately after use with detergent and water.

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-TEX™ PRIMER
ELASTO-TEX™ CAULK
ELASTO-TEX™ DECK COATING

A Liquid applied, single-component, acrylic deck covering system. The system consists of FIBERGLASS MAT saturated with ELASTO-TEX™ BASE COAT by roller, sprayed with ELASTO-TEX™ TEXTURE COAT, followed by ELASTO-TEX™ TOP COAT applied by roller. Conforms to all known V.O.C. requirements in the State of California.

BASIC USES:
For waterproofing areas such as patios, sundecks, stairways, balconies,etc. ELASTO-TEX™ DECK COATING can be used in situations where a skidproof, wear resistant surface is required. It may be used on new decks as well as old concrete decks which are damaged or cracked. The system is suitable for exterior applications where a deck surface must be accessible for foot traffic the same day such as retrofit work. ELASTO-TEX™ DECK COATING can be used in situations where a skidproof, wear resistant surface is required, on new decks as well as old concrete decks which are damaged or cracked. The complete system is approximately 3/16" (4.8mm) thick.

APPLICATION:
Cover all areas to receive ELASTO-TEX™ DECK COATING with fiberglass mat butting edges together without overlapping the mat. Overapplying the fiberglass mat will result in unsightly seams in the finished system. Saturate the fiberglass thoroughly with the ELASTO-TEX™ BASE COAT at the rate of 50 sq. ft. per gallon (1.2 m²/liter), by applying with a roller, adhering the system to the substrate. Allow to cure a minimum of 2-3 hours based at 77°F (25°C). Apply ELASTO-TEX™ TEXTURE COAT by spraying at the rate of 75-100 sq. ft. per gallon (1.8-2.4 m²/liter). Different size textures can be applied by adjusting the hopper gun. Allow texture coat to cure approximately 2-3 hours. Apply ELASTO-TEX™ TOP COAT by roller at the rate of 100 sq. ft. per gallon (2.4 m²/liter). Allow 2-3 hours prior to allowing light foot traffic and 72 hours before allowing heavy traffic.

Parking Deck System with Metal Grit Non-Skid Finish in 42 colors for waterproofing parking decks, roofs, and stadiums.
TECH DATA SHEET | PRODUCT BULLETIN
APPLICATION GUIDE | MAINTENANCE MANUAL
AVAILABLE COLOR:

SURFACE PREPARATION:
All surfaces which are to be coated must be free of contamination such as curing compounds, concrete hardeners, bond breakers, paint, etc. We recommend water-curing concrete instead of using concrete curing compounds. All surfaces must be clean,sound and dry. A light broom-finish is recommended for concrete surfaces. Sandblasting is recommended when possible, otherwise acid etching and wirebrushing may be sufficient. All solvents must be allowed to evaporate off before application over DECK-THANE™ PRIMER.

Except for non-moving shrinkage cracks, all other cracks and joints must be sealed with ELASTO-THANE™ 230, a single-component, polyurethane sealant. All surfaces, where necessary, must be primed with DECK-THANE™ PRIMER (or the primer specified in the product’s documentation) prior to application of the coating system, except for plywood in good condition. All surfaces must be structurally sound and adequately sloped to drain. Only exterior grade plywood, c.c.-plugged and sanded, in conformance with U.S. product standard PSI-66, must be used. Plywood must be installed with all joints tightly butted and properly blocked to prevent differential deflection between plywood panels. Only ring shank nails must be used 4" (10.2 cm) o.c. along panel edges and 8" (20.3 cm) o.c. at intermediate supports.

For best results, the surface that has been coated with DECK-THANE™ PRIMER should be allowed to cure for a minimum of 2 hours before the application of the polyurethane membrane or joint sealant. If for some reason the primer is allowed to cure in excess of 8 hours, the surface should be sanded and reprimed with DECK-THANE™ PRIMER. DECK-THANE™ PRIMER should not be applied over wet surfaces as full adhesion and penetration will not be obtained. Recommended coverage is approximately 250 sq.ft. per gallon on rough surfaces to 350 sq.ft. per gallon on smooth surfaces.

FLASHING:
Metal flashing must be installed at all locations where the horizontal deck joins a vertical surface and at all deck penetrations. Flashing must be nailed 2" (5 cm) o.c. and must be primed with STAINLESS STEEL PRIMER. All seams between plywood sheets and the transition from the metal flashing to the plywood deck must be reinforced by imbedding
a 3-inch wide strip of glass cloth tape into wet ELASTO-DECK™, which is brushed evenly over the seam to a width of about 4 inches (10cm) and a thickness of about 20 mils (.50mm) wet.
The application of ELASTO-DECK™ can subsequently be made immediately over the entire area including the taped areas.

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-THANE™ 230
DECK-THANE™ PRIMER
STAINLESS STEEL PRIMER
ELASTO-DECK™ 5001
ELASTO-GLAZE™ 6001 AL

Water-based epoxy with zero VOCs for priming dry metal, concrete, and wood with easy clean-up.
TECH DATA SHEET | APPLICATION GUIDE | MAINTENANCE MANUAL
AVAILABLE COLOR:

SURFACE PREPARATION:
All surfaces must be clean, dry and sound. Do not apply over damp concrete. Do not over-apply the primer. All water must be allowed to evaporate before application of the deck coating or joint sealant. For best results, the surface that has been coated with ELASTO-POXY™ PRIMER WB should be coated over within 8 hours, or it will have to be reprimed with another coat of ELASTO-POXY™ PRIMER WB. Tools and equipment should be cleaned immediately after use with detergent and water. Recommended coverage is approximately 250 sq.ft. per gallon on rough surfaces to 350 sq.ft. per gallon on smooth surfaces.

Except for non-moving shrinkage cracks, all other cracks and joints must be sealed with ELASTO-THANE™ 230, a single-component, polyurethane sealant. All surfaces, where necessary, must be primed prior to application of the coating system, except for plywood in good condition. All surfaces must be structurally sound and adequately sloped to drain. Only exterior grade plywood, c.c.-plugged and sanded, in conformance with U.S. product standard PSI-66, must be used. Plywood must be installed with all joints tightly butted and properly blocked to prevent differential deflection between plywood panels. Only ring shank nails must be used 4" (10.2 cm) o.c. along panel edges and 8" (20.3 cm) o.c. at intermediate supports.

FLASHING:
Metal flashing must be installed at all locations where the horizontal deck joins a vertical surface and at all deck penetrations. Flashing must be nailed 2" (5 cm) o.c. and must be primed with STAINLESS STEEL PRIMER. All seams between plywood sheets and the transition from the metal flashing to the plywood deck must be reinforced by imbedding
a 3-inch wide strip of glass cloth tape into wet ELASTO-DECK™, which is brushed evenly over the seam to a width of about 4 inches (10cm) and a thickness of about 20 mils (.50mm) wet.
The application of ELASTO-DECK™ can subsequently be made immediately over the entire area including the taped areas.

MSDS DOCUMENTS FOR THESE SYSTEMS:
ELASTO-THANE™ 230
ELASTO-THANE™ 500
STAINLESS STEEL PRIMER
ELASTO-DECK™ 5001
ELASTO-GLAZE™ 6001 AL
ELASTO-DECK™ BT - Type I
ELASTO-DECK™ BT - Type II
ELASTO-POXY™ WB PRIMER PART-A
ELASTO-POXY™ WB PRIMER PART-B

Solvent-based, VOC compliant epoxy for priming metal, dry or damp concrete, and wood under adverse conditions.
TECH DATA SHEET | APPLICATION GUIDE | MAINTENANCE MANUAL
AVAILABLE COLORS:

A two-component, epoxy resin based concrete, metal, and wood primer for use with ELASTO-DECK™ 5000 and ELASTO-DECK™ BT Systems. The primer may also be used with other polyurethane and epoxy systems, including joint sealants. Modified Bisphenol A-Epichlorohydrin epoxy resin cured with an Amine hardener to set up to a durable tough film when used on wood, metal, or concrete (including damp or green). ELASTO-POXY™ PRIMER (VOC) is specially formulated as a primer for polyurethane coatings that are to be put down under conditions which would normally be considered adverse for application. On green concrete (concrete that is more than 8 days, but less than 28 days old), concrete floors poured in metal pans, or where the surrounding water table might cause a damp condition, ELASTO-POXY™ PRIMER (VOC) will set up to form a sound surface for polyurethanes and epoxies to bond to. ELASTO-POXY™ PRIMER (VOC) also has excellent adhesion to metal and wood surfaces.

SURFACE PREPARATION:
All surfaces must be clean, dry and sound. Do not apply over damp concrete. Do not over-apply the primer. All water must be allowed to evaporate before application of the deck coating or joint sealant. For best results, the surface that has been coated with ELASTO-POXY™ PRIMER (VOC) should be coated over within 8 hours, or it will have to be reprimed with another coat of ELASTO-POXY™ PRIMER (VOC). Tools and equipment should be cleaned immediately after use with detergent and water. Recommended coverage is approximately 250 sq.ft. per gallon on rough surfaces to 350 sq.ft. per gallon on smooth surfaces.

Except for non-moving shrinkage cracks, all other cracks and joints must be sealed with ELASTO-THANE™ 230, a single-component, polyurethane sealant. All surfaces, where necessary, must be primed prior to application of the coating system, except for plywood in good condition. All surfaces must be structurally sound and adequately sloped to drain. Only exterior grade plywood, c.c.-plugged and sanded, in conformance with U.S. product standard PSI-66, must be used. Plywood must be installed with all joints tightly butted and properly blocked to prevent differential deflection between plywood panels. Only ring shank nails must be used 4" (10.2 cm) o.c. along panel edges and 8" (20.3 cm) o.c. at intermediate supports.

FLASHING:
Metal flashing must be installed at all locations where the horizontal deck joins a vertical surface and at all deck penetrations. Flashing must be nailed 2" (5 cm) o.c. and must be primed with STAINLESS STEEL PRIMER. All seams between plywood sheets and the transition from the metal flashing to the plywood deck must be reinforced by imbedding
a 3-inch wide strip of glass cloth tape into wet ELASTO-DECK™, which is brushed evenly over the seam to a width of about 4 inches (10cm) and a thickness of about 20 mils (.50mm) wet.
The application of ELASTO-DECK™ can subsequently be made immediately over the entire area including the taped areas.

MSDS DOCUMENTS FOR THESE SYSTEMS:
ELASTO-POXY™ PRIMER (VOC) - Part A
ELASTO-POXY™ PRIMER (VOC) - Part B
ELASTO-THANE™ 230
ELASTO-THANE™ 500
STAINLESS STEEL PRIMER
ELASTO-DECK™ 5001
ELASTO-GLAZE™ 6001 AL
ELASTO-DECK™ BT - Type I
ELASTO-DECK™ BT - Type II

Solvent-based epoxy for priming metal, dry or damp concrete, and wood under adverse conditions.
TECH DATA SHEET | APPLICATION GUIDE | MAINTENANCE MANUAL
AVAILABLE COLORS:

A two-component, epoxy resin based concrete, metal, and wood primer for use with ELASTO-DECK™ 5000 and ELASTO-DECK™ BT Systems. The primer may also be used with other polyurethane and epoxy systems, including joint sealants. Modified Bisphenol A-Epichlorohydrin epoxy resin cured with an Amine hardener to set up to a durable tough film when used on wood, metal, or concrete (including damp or green). ELASTO-POXY™ PRIMER is specially formulated as a primer for polyurethane coatings that are to be put down under conditions which would normally be considered adverse for application. On green concrete (concrete that is more than 8 days, but less than 28 days old), concrete floors poured in metal pans, or where the surrounding water table might cause a damp condition, ELASTO-POXY™ PRIMER will set up to form a sound surface for polyurethanes and epoxies to bond to. ELASTO-POXY™ PRIMER also has excellent adhesion to metal and wood surfaces.

SURFACE PREPARATION:
All surfaces must be clean, dry and sound. Do not apply over damp concrete. Do not over-apply the primer. All water must be allowed to evaporate before application of the deck coating or joint sealant. For best results, the surface that has been coated with ELASTO-POXY™ PRIMER should be coated over within 8 hours, or it will have to be reprimed with another coat of ELASTO-POXY™ PRIMER. Tools and equipment should be cleaned immediately after use with detergent and water. Recommended coverage is approximately 250 sq.ft. per gallon on rough surfaces to 350 sq.ft. per gallon on smooth surfaces.

Except for non-moving shrinkage cracks, all other cracks and joints must be sealed with ELASTO-THANE™ 230, a single-component, polyurethane sealant. All surfaces, where necessary, must be primed prior to application of the coating system, except for plywood in good condition. All surfaces must be structurally sound and adequately sloped to drain. Only exterior grade plywood, c.c.-plugged and sanded, in conformance with U.S. product standard PSI-66, must be used. Plywood must be installed with all joints tightly butted and properly blocked to prevent differential deflection between plywood panels. Only ring shank nails must be used 4" (10.2 cm) o.c. along panel edges and 8" (20.3 cm) o.c. at intermediate supports.

FLASHING:
Metal flashing must be installed at all locations where the horizontal deck joins a vertical surface and at all deck penetrations. Flashing must be nailed 2" (5 cm) o.c. and must be primed with STAINLESS STEEL PRIMER. All seams between plywood sheets and the transition from the metal flashing to the plywood deck must be reinforced by imbedding
a 3-inch wide strip of glass cloth tape into wet ELASTO-DECK™, which is brushed evenly over the seam to a width of about 4 inches (10cm) and a thickness of about 20 mils (.50mm) wet.
The application of ELASTO-DECK™ can subsequently be made immediately over the entire area including the taped areas.

MSDS DOCUMENTS FOR THESE SYSTEMS:
ELASTO-THANE™ 230
ELASTO-THANE™ 500
STAINLESS STEEL PRIMER
ELASTO-DECK™ 5001
ELASTO-GLAZE™ 6001 AL
ELASTO-DECK™ BT - Type I
ELASTO-DECK™ BT - Type II
ELASTO-POXY™ PRIMER PART-A
ELASTO-POXY™ PRIMER PART-B

Silane-based primer for preparing existing membranes and coatings for new polyurethane.
TECH DATA SHEET
AVAILABLE COLOR:

A one component, reactive silane based primer specifically designed to promote adhesion to existing membranes and coatings used to promote the adhesion of all of our polyurethane coatings to previously applied coatings, which are in good condition and well bonded to the substrate. NOTE: This product is not compliant with the new California SCAQMD Rule 1113. Please check with your local air quality district to verify that it meets their requirements.

APPLICATION:
Application of this primer to these surfaces is best accomplished by spray method. When applying to previously applied coatings other than our polyurethane systems, a check and test for adhesion is required. All surfaces which are to be coated with INTER-COAT ADHESION PRIMER must be free of contamination, un-sound paints, or oxidation, etc. All surfaces must be clean, sound and dry. Power washing and scrubbing may be required to prepare the surface. A minimum of two hours drying time is mandatory in all cases. If for some reason the primer is allowed to cure in excess of 8 hours, the surface should be reprimed with INTER-COAT ADHESION PRIMER.

COVERAGE:
250 sq. ft. per gallon on rough surfaces. Up to 350 sq.ft. per gallon on smooth surfaces. All solvents must be allowed to evaporate off before application of new coating over INTER-COAT ADHESION PRIMER. It is imperative that the surface that has been coated with INTER-COAT ADHESION PRIMER be allowed to cure for a minimum of 2 hours before being coated. If for some reason the primer is allowed to cure in excess of 8 hours, the surface should be reprimed with INTER-COAT ADHESION PRIMER before being coated. INTER-COAT ADHESION PRIMER should not be applied over wet surfaces, as full adhesion will not be obtained. Apply by brush, roller or spray. Containers that have been opened must be used up within one or two days since it is a moisture-sensitive product.

CLEAN-UP:
Because of the difficulty in cleaning up or removing cured INTER-COAT ADHESION PRIMER, equipment and tools should be cleaned immediately after use with ACETONE. Use only water based hand cleaners for skin clean up.

MSDS DOCUMENTS FOR THIS SYSTEM:
INTERCOAT ADHESION PRIMER

Epoxy resin primer with a special hardener for use on damp and green concrete that may ne applied under adverse conditions.
TECH DATA SHEET | APPLICATION GUIDE | MAINTENANCE MANUAL
AVAILABLE COLORS:

A two-component, epoxy resin based primer for use with ELASTO-DECK™ 5000 and ELASTO-DECK™ BT Systems. The primer may also be used with other polyurethane and epoxy systems. Modified epoxy resin cured with a special hardener to set up to a durable tough film when used on damp or green concrete. ELASTO-POXY™ PRIMER DG is specially formulated as a clear primer for polyurethane coatings that are to be put down under conditions which would normally be considered adverse for application, e.g. rainy, cold climates. Concrete may be damp, but must be surface dry. On green concrete (concrete that is more than 8 days, but less than 28 days old), concrete floors poured in metal pans, or where the surrounding water table might cause a damp condition, ELASTO-POXY™ PRIMER DG will set up to form a sound surface for polyurethanes to bond to. It also has excellent adhesion to wood surfaces. Equipment and tools should be cleaned immediately after use with Acetone, because of the difficulty in cleaning up or removing cured ELASTO-POXY™ PRIMER DG.

SURFACE PREPARATION:
All surfaces must be clean, dry and sound. Do not apply over damp concrete. Do not over-apply the primer. All water must be allowed to evaporate before application of the deck coating or joint sealant. For best results, the surface that has been coated with ELASTO-POXY™ PRIMER DG should be coated over within 8 hours, or it will have to be reprimed with another coat of ELASTO-POXY™ PRIMER DG. Tools and equipment should be cleaned immediately after use with detergent and water. Approximately 250 sq. ft. per gallon is the recommended coverage, however, porous surface conditions will require slightly more material. ELASTO-POXY™ PRIMER DG may be applied as low as 45°F. Do not thin!

Except for non-moving shrinkage cracks, all other cracks and joints must be sealed with ELASTO-THANE™ 230, a single-component, polyurethane sealant. All surfaces, where necessary, must be primed prior to application of the coating system, except for plywood in good condition. All surfaces must be structurally sound and adequately sloped to drain. Only exterior grade plywood, c.c.-plugged and sanded, in conformance with U.S. product standard PSI-66, must be used. Plywood must be installed with all joints tightly butted and properly blocked to prevent differential deflection between plywood panels. Only ring shank nails must be used 4" (10.2 cm) o.c. along panel edges and 8" (20.3 cm) o.c. at intermediate supports.

FLASHING:
Metal flashing must be installed at all locations where the horizontal deck joins a vertical surface and at all deck penetrations. Flashing must be nailed 2" (5 cm) o.c. and must be primed with STAINLESS STEEL PRIMER. All seams between plywood sheets and the transition from the metal flashing to the plywood deck must be reinforced by imbedding
a 3-inch wide strip of glass cloth tape into wet ELASTO-DECK™, which is brushed evenly over the seam to a width of about 4 inches (10cm) and a thickness of about 20 mils (.50mm) wet.
The application of ELASTO-DECK™ can subsequently be made immediately over the entire area including the taped areas.

MSDS DOCUMENTS FOR THESE SYSTEMS:
ELASTO-THANE™ 230
ELASTO-THANE™ 500
STAINLESS STEEL PRIMER
ELASTO-DECK™ 5001
ELASTO-GLAZE™ 6001 AL
ELASTO-DECK™ BT - Type I
ELASTO-DECK™ BT - Type II
ELASTO-POXY™ PRIMER DG PART-A
ELASTO-POXY™ PRIMER DG PART-B

Promotes adhesion of polyurethane coatings and joint sealants to most metal surfaces, including stainless steel.
TECH DATA SHEET | APPLICATION GUIDE
AVAILABLE COLOR:

All surfaces which are to be coated with STAINLESS STEEL PRIMER must be free of contamination such as paints, powdered coatings, oxidation, etc. All surfaces must be clean, sound and dry. Sandblasting is recommended, although, wirebrushing may be sufficient.

APPLICATION:
All solvents must be allowed to evaporate off before application over STAINLESS STEEL PRIMER. All surfaces must be clean, sound, and dry. For best results, the surface that has been coated with STAINLESS STEEL PRIMER should be allowed to cure for a minimum of 30 minutes before being coated or caulked over. If for some reason the primer is allowed to cure in excess of 24 hours, the surface should be reprimed with STAINLESS STEEL PRIMER. Recommended coverage is approximately 350 sq. ft. per gallon.

CRACKS AND JOINTS:
Except for non-moving shrinkage cracks, all other cracks and joints must be sealed with ELASTO-THANE™ 230, a single-component, polyurethane sealant. All surfaces, where necessary, must be primed prior to application of the coating system, except for plywood in good condition. All surfaces must be structurally sound and adequately sloped to drain. Only exterior grade plywood, c.c.-plugged and sanded, in conformance with U.S. product standard PSI-66, must be used. Plywood must be installed with all joints tightly butted and properly blocked to prevent differential deflection between plywood panels. Only ring shank nails must be used 4" (10.2 cm) o.c. along panel edges and 8" (20.3 cm) o.c. at intermediate supports.

FLASHING:
Metal flashing must be installed at all locations where the horizontal deck joins a vertical surface and at all deck penetrations. Flashing must be nailed 2" (5 cm) o.c. and must be primed with STAINLESS STEEL PRIMER. All seams between plywood sheets and the transition from the metal flashing to the plywood deck must be reinforced by imbedding
a 3-inch wide strip of glass cloth tape into wet ELASTO-DECK™, which is brushed evenly over the seam to a width of about 4 inches (10cm) and a thickness of about 20 mils (.50mm) wet.
The application of ELASTO-DECK™ can subsequently be made immediately over the entire area including the taped areas.

COVERAGE:
Approximately 350 sq. ft. per gallon (7.35 m²/liter) is recommended coverage. All solvents must be allowed to evaporate off before application over STAINLESS STEEL PRIMER is possible. For best results, the surface that has been coated with STAINLESS STEEL PRIMER should be allowed to cure for a minimum of 30 minutes before being coated or caulked over. If for some reason the primer is allowed to cure in excess of 24 hours, the surface should be reprimed with STAINLESS STEEL PRIMER. Do not apply over wet surfaces as full adhesion and penetration will not be obtained. STAINLESS STEEL PRIMER may be applied by brush, roller or spray. Containers that have been opened must be used up within one or two days since it is a moisture-sensitive product.

CLEAN-UP:
Because of the difficulty in cleaning up or removing cured STAINLESS STEEL PRIMER, equipment and tools should be cleaned immediately after use with Acetone. Use only water based hand cleaners for skin clean up. A one component, reactive silane based primer for metal surfaces used to promote adhesion of our polyurethane coating systems and joint sealants to most metal surfaces. This includes all of our one and two component polyurethane based coatings and joint sealants.

MSDS DOCUMENTS FOR THESE SYSTEMS:
ELASTO-THANE™ 230
STAINLESS STEEL PRIMER