A low odor, no solvent polyurea that is insensitive to moisture. A weathertight seal for all types of building joints, such as masonry and metal curtain walls, perimeter joints of sashes, panels and doors, water reservoirs, etc where an embedded color match is important.
TECH DATA SHEET | PRODUCT BULLETIN
AVAILABLE COLORS:

TYPE I: Self-Leveling/Pourable | TYPE II: Gungrade/Non-Sag
A low modulus, polyurea joint sealant, which cures to a firm, flexible, tear-resistant rubber. It is highly resilient and has excellent recovery characteristics after extended periods of compression or elongation. Both Type I and Type II are 100% V.O.C. Free materials. ELASTO-THANE™ 920 is designed to tolerate significant joint movement, up to ±25%. Unlike conventional polyurethane sealants, both components are insensitive to moisture, therefore, the containers may be opened and re-sealed without the material setting up. It contains no solvents, therefore, contains no strong odors, and consists of an “A” Component (Base), “B” Component (Catalyst), and a color pak.

BASIC USES:
ELASTO-THANE™ 920 is a general purpose sealant providing a flexible, durable, weathertight seal for all types of building joints, such as expansion joints in masonry and metal curtain walls, perimeter joints of sashes, panels and doors, non-potable water reservoirs, etc.

JOINT DESIGN:

• The spacing and number of joints, as well as the joint width, should be designed to limit total joint movement to ±25%.
• The depth of the sealant, including its shape, should be controlled by using acceptable joint fillers or backing rod materials. Polyethylene rod or polyurethane foam is recommended as a joint-filler and back up material. Fillers treated with bituminous products, grease or oil, must not be used. Where present, contaminants must be completely removed or separated by vinyl tape or polyethylene film.
• A bond breaker tape, or polyethylene strip, should be used in shallow joints, which do not allow the use of a backerrod. Either a backer rod or bond breaker tape must be used to prevent three-sided adhesion.
• Suitable for all properly designed joints following accepted engineering practices. Joint width must be a minimum of 4 times the anticipated movement.

SURFACE PREPARATION:

• All joints must be absolutely clean and dry. For concrete joints, sandblasting is recommended. All curing compounds, old caulks, grease, waterproofing compounds, wax, rust, paint, curing compounds, loose debris, etc. must be removed.
• For non-porous surfaces such as glass, metal, etc., cleaning with Acetone is recommended. Do not use Toluene, as it leaves an oily surface.

PRIMING:

• ELASTO-THANE™ 920 is a self-priming sealant, therefore, a primer is not normally required.
• However, for submerged applications or damp joints, prime all joints with Elasto-Poxy™ Primer prior to installation. The Elasto-Poxy™ Primer must dry for approximately 1 hour at 77°F and 50% R.H. before installing the ELASTO-THANE™ 920.
• The contractor should test the adhesion of the sealant at the job site in order to verify that proper adhesion is being obtained.

MIXING:

• ELASTO-THANE™ 920 is a two-component material, plus a separate color pak, and must be mechanically mixed prior to use.
• The "A" Component, "B" Component, and color pak are all pre-proportioned, at the factory, which eliminates the need for job site measuring. Mix complete kits only.
• Empty entire contents of "B" Component and color-pak into the "A" Component pail. Mix thoroughly for 5 minutes, using a low speed drill and Jiffy mixing blade. Avoid whipping air into the material.
• During the mixing procedure, scrape the bottom and the sides of the container to ensure that the "A" Component, "B" Component, and color pak are thoroughly mixed, and that the color is uniform.

APPLICATION:

• After the ELASTO-THANE™ 920 has been completely mixed, the sealant must be drawn into a bulk caulking gun, or the bulk caulking gun may be filled using a "follower plate" device.
• Apply ELASTO-THANE™ 920 continuously using sufficient pressure to fill the entire width and depth of the joint, from the bottom up.
• The tooling device may be wiped with a solvent, such as Xylene, to achieve a smooth, properly tooled joint.
• For Horizontal Joints, ELASTO-THANE™ 920 Type I, Pourable may be used where the slope does not exceed 2%. A firm backing material is required beneath horizontal joints in order to help the sealant resist puncturing from high heel traffic.

LIMITATIONS:
ELASTO-THANE™ 920 is not recommended for areas subject to harsh chemical immersion, and special architectural finishes without prior testing. Joints that are subjected to water immersion, such as non-potable reservoirs, canals, water tanks, ponds, etc., may be caulked if the Elasto-Poxy™ Primer is used to prime the joints prior to installing the sealant. ELASTO-THANE™ 920 is recommended for expansion joints subjected to severe movement, where a low modulus sealant is required.

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-POXY™ PRIMER - Part A
ELASTO-POXY™ PRIMER - Part B
ELASTO-THANE™ 920 PART-A
ELASTO-THANE™ 920 PART-B

An extremely high shore, semi-rigid polyurea that prevents industrial vehicle traffic from spalling (breaking) off saw-cut joint edges. Allows floors to be re-opened to normal traffic within just 1 hour!
TECH DATA SHEET | PRODUCT BULLETIN
AVAILABLE COLORS:

ADVANTAGES:

• Semi-Rigid Polyurea
• One-Hour Cure at Any Ambient Temperature
• Extremely High Shore Hardness (80A - 90A)
• Shaves Cleanly
• Resists Chemicals
• Non-Staining
• Resistant to Chemicals
• Color can be Custom Matched to Almost any Swatch

APPLICATIONS:

• Cold Storage Facilities
• Industrial and Warehouse Floors
• Food Processing Facilities
• Bottling and Canning Plants
• Waste Water Treatment Facilities

CHEMICAL RESISTANCE:
PAC POLYUREA™ 85A is highly chemical resistant. After 7 days of contact at 77°F, testing of over 40 chemicals had no effect. The tests included most common solvents, acids used in chemical and food production, foodstuffs, common household and commercial cleaning fluids, alcohols, and oils. Note: all chemical spills should be cleaned up as soon as possible. Please review the Technical Data Sheet above for complete test results.

JOINT DESIGN:
Joints must be free of dirt, debris, previously applied coatings, sealers, and saw laitance, etc. The most effective joint preparation is dry-cutting with a vacuum-equipped, diamond blade saw. With the blade depth extended to the full filler depth, run it against each sidewall. Vacuum out any remaining debris. Joints or cracks that pass completely through the floor may be choked-off at the bottom with 1/4” of dry silica sand, or thickening the filler by mixing it with sand (for the bottom layer of the joint only) to prevent the liquid from running through.

APPLICATION:
Install with static mixing tips and use power dispensing pumps for larger areas. (Recommended equipment available through: Adhesive Systems Technology Corporation) Joints must be overfilled (crowned). Most concrete coatings will not be stained by the overfill. (Contact Manufacturer for details.) To effectively protect joints edges, PAC POLYUREA™ 85A must be flush with the floor surface. Razor shave the overfilled crown after it has fully cured. For best results, delay joint filling for as long as possible. If filling in refrigerated areas, the room should be stabilized at its final operating temperature for more than 7 days before filling joints. Joints should be dry at the time of installation, and the work area should be well ventilated. New floors should have a minimum cure-time of 30 days prior to application of PAC POLYUREA™ 85A.
Note: DO NOT USE COMPRESSIBLE MATERIALS OR BACKER RODS IN SAW CUT JOINTS.

MSDS DOCUMENTS FOR THIS SYSTEM:
PAC POLYUREA™ 85 PART-A
PAC POLYUREA™ 85 PART-B

Liquid applied, flexible polyurea for waterproofing any substrate, including foam roofs, that can help projects achieve USGBC LEED Green Building certification and Tier 2 utility rebates.
TECH DATA SHEET | TITLE 24 CERTIFICATION | PRODUCT BULLETIN
AVAILABLE COLORS:

FOAM ROOF RETROFITS
Roof coatings should be applied after the polyurethane foam degassing period, typically about 8 hours. If the foam cannot be coated immediately or within 48 hours and it oxidizes, the surface should be mechanically scarfed or sanded. Resistant to chemicals, UV rays, and extreme weather (including hail), this 100% solids, zero VOC, liquid applied, flexible, elastomeric polyurea roof coating and waterproofing system is available in White, Concrete Grey, and Tan, as well as custom matched colors (with minimum quantities). It is highly resistant to peel in high winds.

BENEFITS AND SAVINGS

• CRRC Cool Roof Approved
• EnergyStar® Approved
• U.S. Green Building Council - Highest LEED™ Credits
• Top Tier Utility Rebates
• 100% Tax Deductible - 1st Year
• Durable in Extreme Weather, Resists Hail and High Winds
• Warranty - 5, 10, and 10 + 5 Year
• Renewable and Sustainable
• Save 30% of HVAC costs
• Safe - Cold Applied, No hot kettles
• No tear-off, No waste disposal

COATS OVER ANY EXISTING SUBSTRATE (*Please consult with a Pacific Polymers technical consultant for specific instructions and methods for each substrate.)

• Polyurethane Foam
• Concrete
• Asphalt
• Plywood
• Modified Bitumen
• Smooth Surface Emulsion
• Previously Coated Roofs
• BUR (Built-Up Roofs)
• Single-Ply
• Metal Roofs
• Corrugated Roofs

MSDS DOCUMENTS FOR THESE SYSTEMS:
ELASTO-DECK™ 6500RC2 PART-A
ELASTO-DECK™ 6500RC2 PART-B

Low odor, 100% solids, aliphatic polyurea coating system for walking or parking decks, and concrete pipes.
TECH DATA SHEET | MAINTENANCE MANUAL
AVAILABLE COLORS:

A two component, Zero VOC, virtually no odor, elastomeric polyurea traffic coating system for waterproofing walking decks, balconies, plazas, parking decks, mechanical room floors, and concrete pipes. Concrete or Plywood substrates. All surfaces must be completely free of foreign matter and primed with ELASTO-POXY™ PRIMER WATERBASED, where necessary. ELASTO-DECK™ 6500 has a very short work life, so once it is mixed, the coating must be poured onto surface and applied immediately.

SURFACE PREPARATION:
All surfaces which are to receive ELASTO-DECK™ 6500 shall be free of contamination such as water, curing compounds, hardeners, bond breakers, paint, etc. A light broom finish is recommended for concrete surfaces. It is desirable to watercure concrete in lieu of curing compounds. Contaminants should be removed by sandblasting or acid-etching. If etching is used, allow adequate time for surface to dry. Except for non-moving shrinkage cracks, all other cracks must be sealed with ELASTO-THANE™ 230, a single-component, moisture-cured, polyurethane sealant. All surfaces, where necessary, must be primed with ELASTO-POXY™ WATERBASED PRIMER prior to application of the coating system at a rate of 300-350 square feet per gallon (7.4 – 8.6 m²/liter).

APPLICATION:
Lightly stir the A-Component (pigmented side) for 2-3 minutes using a jiffy mixing blade to evenly distribute the pigments that may have settled to the bottom of the container. Then pour “B” Component (clear side) into the “A” Component. Scrape the container to drain all the “B” Component into the “A” Component. Mix thoroughly using a jiffy mixing blade attached to a low speed drill to a uniform color without any streaks. Mix for 2-3 minutes. Once mixed, immediately pour ELASTO-DECK™ 6500 onto the surface of the substrate. Use squeegee to evenly apply the material, then backroll using a roller to break air bubbles.
Note: Higher temperatures will reduce the work life.

ELASTO-DECK™ 6500 shall be applied to the primed concrete at a rate of 80 square feet per gallon. Following a 24 hour cure time, apply the seond coat at the rate of 80 square feet per gallon and while coating is in a fluid condition, broadcast desired aggregate at the rate of 10-15 pounds per 100 square feet and backroll to ensure even distribution of the grit. Allow a minimum of 72 hours cure time before allowing any heavy traffic on the finished system.

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-THANE™ 230
ELASTO-POXY™ PRIMER PART-A
ELASTO-POXY™ PRIMER PART-B
ELASTO-DECK™ 6500 PART-A
ELASTO-DECK™ 6500 PART-B

Fluid applied 100% solids, zero VOC, waterproof, pedestrian traffic deck coating on plywood substrate. Low odor aliphatic polyurea coating system for walking decks.
TECH DATA SHEET | PRODUCT BULLETIN | MAINTENANCE MANUAL
AVAILABLE COLORS:

A two component, liquid applied, flexible, low odor, aliphatic, 100% solids, Zero VOC, elastomeric polyurea, traffic coating system for walking deck surfaces. Concrete or Plywood substrates.

BASIC USES:
For waterproofing walking decks, balconies plazas, parking decks, mechanical room floors, etc. Designed for pedestrian traffic.

ADVANTAGES:

• 100% Solids
• Low Odor/Zero VOC
• Waterproof
• Elastomeric
• Fast Setting

APPLICATIONS:

• Pedestrian Decks
• Stadiums
• Balconies
• Plazas
• Roof Decks

SURFACE PREPARATION:
All surfaces which are to receive ELASTO-DECK™ 6500 PT shall be free of contamination such as water, curing compounds, hardeners, bond breakers, paint, etc. A light broom finish is recommended for concrete surfaces. It is desirable to watercure concrete in lieu of curing compounds. Contaminants should be removed by sandblasting or beadblasting. Except for non-moving shrinkage cracks, all other cracks must be sealed with ELASTO-DECK™ 6500 PT and taped with 4" Tietex. All surfaces, where necessary, must be primed with ELASTO-POXY™ PRIMER (VOC) prior to application of the coating system at a rate of 200-250 square feet per gallon.

APPLICATION:
Lightly stir the A-Component (pigmented side) for 2-3 minutes using a jiffy mixing blade to evenly distribute the pigments that may have settled to the bottom of the container. Then pour “B” Component (clear side) into the “A” Component. Scrape the container to drain all the “B” Component into the “A” Component. Mix thoroughly using a jiffy mixing blade attached to a low speed drill to a uniform color without any streaks. Mix for 2-3 minutes. ELASTO-DECK™ 6500 PT has a relatively short work life, so once it is mixed, the coating must be poured onto surface and applied immediately. Use squeegee to evenly apply the material, then backroll using a roller to break air bubbles. Note: Higher temperatures will reduce the work life. Apply to the primed concrete at a rate of 80 square feet per gallon. Following a 24 hour cure time of the ELASTO-DECK™ 6500 PT, apply the ELASTO-DECK™ 6500 PT at the rate of 80 square feet per gallon and while coating is in a fluid condition, broadcast desired aggregate at the rate of 10-15 pounds per 100 square feet and backroll to ensure even distribution of the grit. Allow a minimum of 72 hours curetime before allowing any heavy traffic on the finished system.

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-DECK™ 6500 PT-A
ELASTO-DECK™ 6500 PT-B

Cold, fluid applied membrane with zero solvents and no VOC’s that is safe and ideal for use in occupied structures.
TECH DATA SHEET
AVAILABLE COLOR:

Type I: For horizontal surfaces
Type II: For vertical surfaces
A black, liquid applied, two-component, 100% solids, polyurea system, designed to form a tough rubber membrane impervious to moisture. A technological breakthrough! A solvent-free, Iso-cyanate free, polyurea elastomer. Will cure to a tough, waterproof membrane, independent of atmospheric moisture. Once cured, ENVIRO-SHIELD™ allows expansion and contraction over a broad temperature range and maintains flexibility and waterproofing properties under continuous exposure to water above or below grade. Best applied by airless spray. ENVIRO-SHIELD™ remains flexible from -75° to 175°F.
Note: this is not a traffic bearing system.

WATERPROOFING USES:

• In between concrete slabs, parking and roof decks, or courtyards over subterranean parking
• Below grade exterior walls or foundations and basements or other structures to be backfilled
• Inside planter boxes
• Under terrazzo or tile floors, showerpans, kitchen, laundry and bathroom floors
• Above occupied areas under malls, plazas and promenades

ADVANTAGES:

• Cold applied in one day, even in hot, dry climates: no hot kettles, no torches, no open flames, no hot seam welders, no noxious vapors or air pollution, no coal tar, safe for workers
• Eliminates splicing, sealing tapes, adhesives and other labor consuming methods
• Superior flexibility and elongation properties allow expansion and contraction with the substrate without cracking or becoming brittle
• Excellent abrasion resistance for applications where there may be contact with floating debris
• May be applied over concrete, stone, brick, cement blocks, wood, metal, and asbestos
• Environmentally safe, complies with VOC standards, ideal for use on occupied structures

MSDS DOCUMENTS FOR THIS SYSTEM:
ENVIRO-SHIELD™ PART-A
ENVIRO-SHIELD™ PART-B

Fluid applied 100% solids, zero VOC, waterproof, pedestrian traffic deck coating on concrete substrate. Low odor aliphatic polyurea coating system for walking or parking decks.
TECH DATA SHEET | PRODUCT BULLETIN | CASE STUDY
MAINTENANCE MANUAL
AVAILABLE COLORS:

A two component, Zero VOC, virtually no odor, elastomeric polyurea traffic coating system for waterproofing walking decks, balconies, plazas, parking decks, mechanical room floors, and concrete pipes. Concrete or Plywood substrates.

ADVANTAGES:

• 100% Solids
• Low Odor/Zero VOC
• Waterproof
• Elastomeric
• Fast Setting

APPLICATIONS:

• Vehicular Traffic
• Parking Deck
• Ramps and Slopes
• Exterior
• Interior

SURFACE PREPARATION:
All surfaces which are to receive ELASTO-DECK™ 6500 VT shall be free of contamination such as water, curing compounds, hardeners, bond breakers, paint, etc. A light broom finish is recommended for concrete surfaces. It is desirable to watercure concrete in lieu of curing compounds. Contaminants should be removed by sandblasting or beadblasting. Except for non-moving shrinkage cracks, all other cracks must be sealed with ELASTO-DECK™ 6500 VT and taped with 4" Tietex. All surfaces, where necessary, must be primed with ELASTO-POXY™ PRIMER (VOC) prior to application of the coating system at a rate of 200-250 square feet per gallon.

APPLICATION:
Lightly stir the A-Component (pigmented side) for 2-3 minutes using a jiffy mixing blade to evenly distribute the pigments that may have settled to the bottom of the container. Then pour “B” Component (clear side) into the “A” Component. Scrape the container to drain all the “B” Component into the “A” Component. Mix thoroughly using a jiffy mixing blade attached to a low speed drill to a uniform color without any streaks. Mix for 2-3 minutes. ELASTO-DECK™ 6500 PT has a relatively short work life, so once it is mixed, the coating must be poured onto surface and applied immediately. Use squeegee to evenly apply the material, then backroll using a roller to break air bubbles. Note: Higher temperatures will reduce the work life. ELASTO-DECK™ 6500 VT shall be applied to the primed concrete at a rate of 80 square feet per gallon. Following a 24 hour cure time of the ELASTO-DECK™ 6500 VT, apply the ELASTO-DECK™ 6500 VT at the rate of 80 square feet per gallon and while coating is in a fluid condition, broadcast desired aggregate at the rate of refusal. After a 24 hour cure, sweep off all loose aggregate and apply ELASTO-DECK™ 6500 VT at a rate of 80 square feet per gallon. Allow a minimum of 72 hours curetime before allowing any heavy traffic on the finished system.

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-DECK™ 6500 VT PART-A
ELASTO-DECK™ 6500 VT PART-B

Pedestrian and Vehicular Deck Coating - Polyurea with user-controlled consistency, shore hardness, and thickness that tolerates extreme movement and harsh environments.
TECH DATA SHEET | MAINTENANCE MANUAL
AVAILABLE COLORS:

A liquid applied, two component, fast curing, 100% solids polyurea coating, applied by special spray equipment, which forms an exceptionally durable finish. ELASTO-DECK™ 8000 coating is a plural component, 100% solid, spray-applied elastomer and is available in an aromatic or aliphatic version. The product is available as a soft, stretch elastomer to a tough, hard elastomer. The coating is dry to the touch in 1 second. It can be applied in any thickness, on horizontal or vertical surfaces.

Perhaps the greatest advantage of this system is its inherent “stress relaxation,” which makes it uniquely suited to bridge cracks. When stretched out, this coating does not recover instantly as do all urethanes, but instead relaxes, thereby removing stress on the material and on the bond line. This feature prevents splitting of the coating over cracks.

BASIC USES:
ELASTO-DECK™ 8000 coating is designed to be spray applied on concrete, metal and wood structures for exterior and interior applications that require waterproofing, specific chemical resistance, corrosion and abrasion protection.

Roofing:
ELASTO-DECK™ 8000 in the aliphatic version is an elastomeric coating for roofs and helipads where an absolutely waterproof coating is crucial, above living quarters and any other occupied areas. ELASTO-DECK™ 8000 is not only limited to new construction but can be used to rehabilitate old, existing built-up, or cap sheet roofs that failed or need repairs. Because of its tenacious bond to most substrates, ELASTO-DECK™ 8000 can be applied directly to the existing roof system. This will help save the extreme costs of removing a built-up roof system.

Traffic Bearing Coating:
ELASTO-DECK™ 8000 can be used as a traffic bearing system, either pedestrian or vehicular traffic. Due to excellent tensile strength and abrasion resistance of ELASTO-DECK™ 8000 as well as availability of a wide range of Shore Hardnesses, it allows the system to be designed to tolerate movement and extreme conditions where other coatings typically fail. When used as a traffic bearing coating, the ELASTO-DECK™ 8000 may require a primer. ELASTO-DECK™ 8000 coating can be applied with an anti-skid surface, which is obtained by holding the spray gun farther from the surface, texture is created by the “in flight” curing of this extremely fast curing elastomer. The sprayed particles of the liquid elastomers do not level out when they hit the deck, thus creating this elastomeric, non-skid texture.
ELASTO-DECK™ 8000 coating has certain uses besides waterproofing, such as:

1. Protective coatings and linings, such as truckbody liners.
2. Abrasion-resistant coatings.
3. Pipe coatings.
4. Soil stabilization.
5. Construction coatings.
6. Grouting.
7. Encapsulation — asbestos, concrete walls, drywall, etc.
8. Highway stripping.
9. Wire bundlings.
10. Industrial coatings.
11. Highway and bridge overlays.
12. Drilling platforms.
13. Tank coatings for non-potable water or hydrocarbon storage.

ADVANTAGES: The Aliphatic coating has:

1. Long term stability toward UV light, enabling them to be used in a variety of outdoor applications.
2. The coating gels within 1-3 seconds after mixing, dries in about 10 seconds and allows traffic within one hour.
3. The sprayed coating is affected very little by weather variations, i.e. rain, high humidity, heat, cold, etc.
4. One coat systems can be sprayed thus reducing time and labor.
5. The coating has excellent physical properties, including tensile strength, elongation and abrasion resistance.
6. High thermal stability at temperatures up to 350°F.
7. Can be sprayed or sloped on vertical surfaces without forming drips or runs.
8. Ease of application. Can be sprayed with commercially available spray application equipment. Little maintenance toward equipment and spray gun.

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-DECK™ 8000 PART-A
ELASTO-DECK™ 8000 PART-B