Trowel applied for smooth pedestrian deck and stairway coatings, even over irregular substrates.
TECH DATA SHEET | MAINTENANCE MANUAL
AVAILABLE COLORS:

ELASTO-DECK™ 1000 is a waterproof, liquid-applied, single-component, moisture-cured, polyurethane deck coating system featuring a smooth troweled finish. The ELASTO-DECK™ 1000 system consists of ELASTO-DECK™ 1001 (elastomeric base coat), ELASTO-GLAZE™ 2001 (liquid polyurethane aggregate binder), and ELASTO-GLAZE™ Type II (aliphatic polyurethane seal coat).

BASIC USES:
Exterior patios, sundecks, balconies, and stairways that require to be water-tight and are subjected to pedestrian traffic. The ELASTO-DECK™ 1000 system is approximately 3/16 inch (4.8mm) thick, but can be installed at greater thicknesses if needed. This system is ideal as a deck covering if the substrate that it is used on has an irregular finish. Since the product is applied with a trowel, it is possible to obtain a smooth finish, if desired, unlike the broadcast system.

SURFACE PREPARATION:
All surfaces which are to be coated with ELASTO-DECK™ 1000 system must be clean and dry. Contamination on concrete, such as curing compounds, bond breakers, paint, or other products, should be removed by acid etching or sandblasting. A light broom finish is recommended on concrete. If a curing compound is used, it should be a sodium silicate based material. It is desirable to water cure concrete instead of using chemical curing compounds. Except for non-moving shrinkage cracks, all cracks and joints must be sealed with ELASTO-THANE™ 230, a single component polyurethane sealant manufactured by Pacific Polymers, Inc.
Concrete must be primed with DECK-THANE™ PRIMER prior to installation of the system. Plywood in good condition does not require priming. All surfaces which are to receive the ELASTO-DECK™ 1000 shall be structurally sound and adequately sloped to drain. Only exterior grade plywood, c.c.-plugged and sanded, in conformance with U.S. product standard PSI-66, must be used. Plywood must be installed with all joints tightly butted and properly blocked to prevent differential deflection between plywood panels. Only ring shank nails must be used 4" (10.2 cm) o.c. along panel edges and 8" (20.3 cm) o.c. at intermediate supports.
Metal flashing must be installed at all locations where the horizontal deck joins a vertical surface and at all deck penetrations. Flashing must be nailed 2" (5 cm) o.c. and must be primed with STAINLESS STEEL PRIMER. All seams between plywood panels and those between metal flashing and plywood must be reinforced by imbedding a 2" (5 cm) wide strip of glass cloth tape into wet ELASTO-DECK™ 1001. The application of ELASTO-DECK™ 1001 can subsequently be made over the entire deck area, including the taped areas.

APPLICATION:
ELASTO-DECK™ 1001 shall be applied at a rate of 60 sq. ft. per gallon (1.47 m²/liter) per coat yielding 25 dry mils (6mm). After an over-night cure, a second application of ELASTO-DECK™ 1001 is to be made at 55 sq. ft. per gallon (1.47 m²/liter), giving an over-all thickness of 50 dry mils (1.27 mm). After a 24 hour cure, apply a mixture of ELASTO-GLAZE™ 2001 and the desired aggregate in a ratio of 5 parts aggregate to 1 part of ELASTO-GLAZE™ 2001 by volume, and trowel to a smooth even finish in a thickness of approximately 3/16 in (4.8 mm). One gallon of ELASTO-GLAZE™ 2001 mixed with 5 gallons of aggregate will cover approximately 40 sq. ft. (12.01 m²). After a 48 hour cure time, apply a coat of ELASTO-GLAZE™ type II at a rate of 110 sq. ft. per gallon (2.45 m²/liter). After a final 24 hour cure time, the deck may be opened to traffic.

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-THANE™ 230
DECK-THANE™ PRIMER
ELASTO-DECK™ 1001
ELASTO-GLAZE™ 2001
ELASTO-GLAZE™ TYPE II

An absolutely waterproof coating for critical areas, such as above residences and offices, available in a natural aggregate or in 42 colors.
TECH DATA SHEET | PRODUCT BULLETIN | CASE STUDY
APPLICATION GUIDE | MAINTENANCE MANUAL
AVAILABLE COLORS:

A liquid-applied, single-component, moisture-cured, polyurethane deck elastomeric deck coating system for walking decks, balconies, patios, roofs, etc., where an absolutely waterproof coating is crucial, such as above living quarters or any other occupied areas. The ELASTO-DECK™ 5000 X2 system consists of a ELASTO-DECK™ 5001 base coat, ELASTO-GLAZE™ 6001 AL top coat and a primer where necessary. ELASTO-DECK™ 5000 X2 is available in a natural aggregate or a pigmented finish.

BASIC USES:
For waterproofing patios, sundecks, stairways, balconies, roofs, etc. ELASTO-DECK™ 5000 X2 can be used on all decks where a waterproof skid-resistant, long-lasting, wear-resistant surface is required. It may be used on new decks as well as on old concrete decks which are damaged, or cracked. The system is suitable for exterior as well as interior applications in all kinds of climates. The coating retains its elastomeric properties in below freezing weather as well as in very hot climates. The complete system including aggregate is approximately 1/8" thick (3.2 mm).

APPLICATION:
ELASTO-DECK™ 5001 shall be applied to the plywood or primed concrete at a rate of 55 square feet per gallon (1.47 m²/liter) resulting in a dry film thickness of 25 mils (.6 mm). After a 24-hour cure, another coat of ELASTO-DECK™ 5001 is applied at the same 25 mil (.6 mm) coverage for a total dry thickness of 50 mils (1.27 mm). ELASTO-DECK™ 5001 Non-Gassing may be substituted for ELASTO-DECK™ 5001 and applied in one coat at the rate of 28 square feet per gallon (0.74 m²/liter). ELASTO-DECK™ 5001 Non-Gassing may be used in a single 50 mil application over sound surfaces without danger of gassing. Application must be made uniformly to avoid thin spots and care must be taken to avoid pinholes and repair them should they occur. ELASTO-DECK™ 5001 Non-Gassing may be accelerated to cure in just a few hours by adding approximately 1/2 fluid ounce of water per gallon of material. Following a 24 hour cure, apply ELASTO-GLAZE™ 6001 AL pigmented, at the rate of 120 square feet per gallon (2.8 m²/liter). Broadcast the desired aggregate into the wet coating to refusal.
After an overnight cure, sweep or blow off all the loose aggregate and apply another coat of ELASTO-GLAZE™ 6001 AL, pigmented or clear at a coverage of 110 square feet per gallon (2.7 m²/liter). Coverage will vary depending on the size of aggregate used. Allow 48 hours cure time before permitting any traffic on the finished system.

MASTER SPECS:
SECTION 07181: (Word file)
TRAFFIC COATINGS ON PLYWOOD
SECTION 07182: (Word file)
TRAFFIC COATINGS ON CONCRETE
SECTION 07183: (Word file)
TRAFFIC COATINGS, HEAVY DUTY ON CONCRETE
SECTION 07570: (pdf)
TRAFFIC TOPPING

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-THANE™ 230
DECK-THANE™ PRIMER
ELASTO-DECK™ 5001
ELASTO-GLAZE™ 6001 AL

CATALYSTS:

Super-Cure™ AL
Catalyst for: Cold Weather and/or Low Humidity
Accelerates the tack free time and cure time of:
1) Elasto-Glaze™ 6001AL
SUPER-CURE™ AL
SUPER-CURE™ AL

Super-Cure™ Rubber
Catalyst for: Cold Weather and/or Low Humidity
Accelerates the tack free time and cure time of:
1) Elasto-Deck™ 5001
SUPER-CURE™ RUBBER
SUPER-CURE™ RUBBER

Wear-resistant, fluid applied, polyurethane deck system for waterproofing parking, walking, and roof decks, with an anti-skid textured finish. It remains flexible even in extreme climates and is available in 42 colors.
TECH DATA SHEET | RESEARCH REPORT
APPLICATION GUIDE | MAINTENANCE MANUAL
AVAILABLE COLORS:

A liquid-applied, single-component, moisture-cured, elastomeric, waterproof coating system for parking decks, roof decks, and walking decks, based on polyurethane elastomers. The system consists of the ELASTO-DECK™ 5001 base coat, ELASTO-GLAZE™ 6001 AL top coat and a primer where necessary. ELASTO-DECK™ 5000 is available in a natural aggregate or pigmented finish. The complete system is approximately 1/8" (3mm) thick. Except for non-moving shrinkage cracks, all other cracks and joints must be sealed with ELASTO-THANE™ 230. All surfaces, where necessary, must be primed with DECK-THANE™ PRIMER.

SURFACE PREPARATION:
All surfaces which are to receive ELASTO-DECK™ 5000 shall be free of contamination such as water, curing compounds, hardeners, bondbreakers, paint, etc. A light broom-finish is recommended for concrete surfaces. It is desirable to watercure concrete in lieu of curing compounds. Contaminants should be removed by bead blasting, sandblasting, or acid etching. If acid etching is used, the area must be properly neutralized and adequate time must be allowed for surface to dry. Except for non-moving shrinkage cracks, all other cracks and joints must be sealed with ELASTO-THANE™ 230, a single-component, polyurethane sealant manufactured by Pacific Polymers, Inc. All surfaces, where necessary, must be primed with DECK-THANE™ PRIMER prior to application of the coating system at a rate of 355 square feet per gallon (8.58 m²/liter), except for plywood in good condition. All seams between plywood sheets and the transition from the metal flashing to the plywood deck must be reinforced by imbedding a 3-inch wide strip of glass cloth tape into wet ELASTO-DECK™ 5001, which is brushed evenly over the seam to a width of about 4 inches (10cm) and a thickness of about 20 mils (.50mm) wet. The application of ELASTO-DECK™ 5001 can subsequently be made immediately over the entire area including the taped areas.

APPLICATION:
ELASTO-DECK™ 5001 shall be applied to exterior grade plywood or primed concrete at a rate of 45 square feet per gallon (1.1 m²/liter) resulting in a 30 dry mil (.7mm) thickness. After a 24-hour cure, apply ELASTO-GLAZE™ 6001 pigmented, at a rate of 120 square feet per gallon (2.82 m²/liter). Broadcast desired aggregate into the wet coating to refusal. After an overnight cure, sweep or blow off all the loose aggregate and apply another coat of ELASTO-GLAZE™ 6001 pigmented or clear, at a rate of 120 square feet per gallon (2.82 m²/liter). Total system thickness is 50 dry mils (1.27mm), excluding aggregate. Allow 48 hours cure time before allowing any traffic on the finished system.

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-DECK™ 5000
ELASTO-GLAZE™ 6001AL
ELASTO-THANE™ 230
DECK-THANE™ PRIMER

CATALYSTS:

Super-Cure™ AL
Catalyst for: Cold Weather and/or Low Humidity
Accelerates the tack free time and cure time of:
1) Elasto-Glaze™ 6001AL
SUPER-CURE™ AL
SUPER-CURE™ AL

Super-Cure™ Rubber
Catalyst for: Cold Weather and/or Low Humidity
Accelerates the tack free time and cure time of:
1) Elasto-Deck™ 5001
SUPER-CURE™ RUBBER
SUPER-CURE™ RUBBER

Fluid applied 100% solids, zero VOC, waterproof, pedestrian traffic deck coating on plywood substrate. Low odor aliphatic polyurea coating system for walking decks.
TECH DATA SHEET | PRODUCT BULLETIN

A two component, liquid applied, flexible, low odor, aliphatic, 100% solids, Zero VOC, elastomeric polyurea, traffic coating system for walking deck surfaces. Concrete or Plywood substrates.

BASIC USES:
For waterproofing walking decks, balconies plazas, parking decks, mechanical room floors, etc. Designed for pedestrian traffic.

ADVANTAGES:

• 100% Solids
• Low Odor/Zero VOC
• Waterproof
• Elastomeric
• Fast Setting

APPLICATIONS:

• Pedestrian Decks
• Stadiums
• Balconies
• Plazas
• Roof Decks

SURFACE PREPARATION:
All surfaces which are to receive ELASTO-DECK™ 6500PT shall be free of contamination such as water, curing compounds, hardeners, bond breakers, paint, etc. A light broom finish is recommended for concrete surfaces. It is desirable to watercure concrete in lieu of curing compounds. Contaminants should be removed by sandblasting or beadblasting. Except for non-moving shrinkage cracks, all other cracks must be sealed with ELASTO-DECK™ 6500PT and taped with 4" Tietex. All surfaces, where necessary, must be primed with ELASTO-POXY™ PRIMER (VOC) prior to application of the coating system at a rate of 200-250 square feet per gallon.

APPLICATION:
Lightly stir the A-Component (pigmented side) for 2-3 minutes using a jiffy mixing blade to evenly distribute the pigments that may have settled to the bottom of the container. Then pour “B” Component (clear side) into the “A” Component. Scrape the container to drain all the “B” Component into the “A” Component. Mix thoroughly using a jiffy mixing blade attached to a low speed drill to a uniform color without any streaks. Mix for 2-3 minutes. ELASTO-DECK™ 6500PT has a relatively short work life, so once it is mixed, the coating must be poured onto surface and applied immediately. Use squeegee to evenly apply the material, then backroll using a roller to break air bubbles. Note: Higher temperatures will reduce the work life. Apply to the primed concrete at a rate of 80 square feet per gallon. Following a 24 hour cure time of the ELASTO-DECK™ 6500PT, apply the ELASTO-DECK™ 6500PT at the rate of 80 square feet per gallon and while coating is in a fluid condition, broadcast desired aggregate at the rate of 10-15 pounds per 100 square feet and backroll to ensure even distribution of the grit. Allow a minimum of 72 hours curetime before allowing any heavy traffic on the finished system.

MASTER SPECS:
SECTION 07184: (Word file)
PEDESTRIAN COATINGS ON PLYWOOD
SECTION 07185: (Word file)
PEDESTRIAN COATINGS ON CONCRETE

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-DECK™ 6500PT-A
ELASTO-DECK™ 6500PT-B

Skid-resistant, low odor acrylic with good UV resistance for athletic surfaces such as tennis courts, etc., may be applied to damp or dry surfaces.
TECH DATA SHEET | PRODUCT BULLETIN | CASE STUDY | CASE STUDY
MAINTENANCE MANUAL
AVAILABLE COLORS:

A single component, skid-resistant coating which provides a tough impervious surface with high resistance to water, greases. It is a one part blend of water base acrylic polymer, epoxy-ester emulsion, and slip resistant aggregates, for liquid application which offers good ultraviolet light resistance. RES-CRIL™ is designed for use on athletic surfaces such as tennis courts, asphalt driveways, and concrete surfaces. This product is recommended for foot traffic areas to reduce slipping on commercial and industrial floors. Due to the waterbased formulation of the product, it can be installed in areas where solvent based coatings are objectionable due to their odors and fire hazards. This material can also be applied over damp as well as dry surfaces.

SURFACE PREPARATION:
Surfaces to be coated must be clean and free of all contaminants that may effect adhesion. Remove any oil or loose paint to provide a clean substrate. Smooth surfaces must be sanded to roughen the texture for proper adhesion. Concrete surfaces must be clean and sound, but need not be thoroughly dry. Slick concrete surfaces require acid washing, neutralizing and flushing prior to application to insure positive adhesion. Bare metal must be primed prior to coating. Do not apply RES-CRIL™ at temperatures below 50°F (10°C). Stir thoroughly before use. Apply RES-CRIL™ with brush, roller, or squeegee at a rate of 150 - 160 sq. feet per gallon (3.70 - 3.90 m²/liter), two coats minimum. Allow 4 hours drying time between coats. Allow a minimum of 12 hours drying time, at normal temperatures, before opening area to light pedestrian traffic.
Clean Up: Brushes and rollers may be cleaned with soap and water immediately after use, followed by a rinse in paint thinner or solvent to remove any oil residue.
Colors: Concrete Grey, Tan, Tennis Court Brown, Tennis Court Green. Special colors available on request.
Sizes: Available in 1 gallon cans and 5 gallon pails.
CAUTION!! Protect this material from freezing temperatures.

MSDS DOCUMENTS FOR THIS SYSTEM:
RES-CRIL™

Fluid applied 100% solids, zero VOC, waterproof, pedestrian traffic deck coating on concrete substrate. Low odor aliphatic polyurea coating system for walking or parking decks.
TECH DATA SHEET | PRODUCT BULLETIN | CASE STUDY
MAINTENANCE MANUAL
AVAILABLE COLORS:

ADVANTAGES:

• 100% Solids
• Low Odor/Zero VOC
• Waterproof
• Elastomeric
• Fast Setting

APPLICATIONS:

• Vehicular Traffic
• Parking Deck
• Ramps and Slopes
• Exterior
• Interior

SURFACE PREPARATION:
All surfaces which are to receive ELASTO-DECK™ 6500VT shall be free of contamination such as water, curing compounds, hardeners, bond breakers, paint, etc. A light broom finish is recommended for concrete surfaces. It is desirable to watercure concrete in lieu of curing compounds. Contaminants should be removed by sandblasting or beadblasting. Except for non-moving shrinkage cracks, all other cracks must be sealed with ELASTO-DECK™ 6500VT and taped with 4" Tietex. All surfaces, where necessary, must be primed with ELASTO-POXY™ PRIMER (VOC) prior to application of the coating system at a rate of 200-250 square feet per gallon.

APPLICATION:
Lightly stir the A-Component (pigmented side) for 2-3 minutes using a jiffy mixing blade to evenly distribute the pigments that may have settled to the bottom of the container. Then pour “B” Component (clear side) into the “A” Component. Scrape the container to drain all the “B” Component into the “A” Component. Mix thoroughly using a jiffy mixing blade attached to a low speed drill to a uniform color without any streaks. Mix for 2-3 minutes. ELASTO-DECK™ 6500VT has a relatively short work life, so once it is mixed, the coating must be poured onto surface and applied immediately. Use squeegee to evenly apply the material, then backroll using a roller to break air bubbles. Note: Higher temperatures will reduce the work life. ELASTO-DECK™ 6500VT shall be applied to the primed concrete at a rate of 80 square feet per gallon. Following a 24 hour cure time of the ELASTO-DECK™ 6500VT, apply the ELASTO-DECK™ 6500VT at the rate of 80 square feet per gallon and while coating is in a fluid condition, broadcast desired aggregate at the rate of refusal. After a 24 hour cure, sweep off all loose aggregate and apply ELASTO-DECK™ 6500VT at a rate of 80 square feet per gallon. Allow a minimum of 72 hours curetime before allowing any heavy traffic on the finished system.

MASTER SPECS:
SECTION 07186: (Word file)
TRAFFIC COATINGS ON CONCRETE

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-DECK™ 6500VT PART-A
ELASTO-DECK™ 6500VT PART-B

Fluid applied, heavy-duty low VOC, waterproof traffic deck coating on concrete substrate. Wear-resistant polyurethane deck system that remains flexible even in extreme climates.
TECH DATA SHEET | APPLICATION GUIDE | MAINTENANCE MANUAL

AVAILABLE COLORS:

ELASTO-DECK™ 5000HT (VOC) is a low VOC, liquid-applied, single component, moisture-cured, seamless, slip resistant, polyurethane, waterproof deck coating. The system consists of ELASTO-DECK™ 5001HT (VOC) BASE COAT and INTERMEDIATE COAT, and ELASTO-GLAZE™ 6001AL HT (VOC) TOP COAT, and a primer, where necessary.

BASIC USES:
For waterproofing parking decks and concrete roof decks. ELASTO-DECK™ 5000 HT (VOC) can be used on all decks where a skid-resistant, long lasting, wear-resistant surface is required. It may be used on new decks as well as on existing concrete decks which are damaged or cracked. The system is suitable for exterior, as well as interior applications in all kinds of climates. The coating retains its elastomeric properties in below freezing weather, as well as in very hot climates.

APPLICATION:
A. Medium and heavy duty decks.
Step (1) ELASTO-DECK™ 5001HT (VOC) shall be applied to the primed concrete at a rate of 64 square feet per gallon (1.57 m²/liter) resulting in a film thickness of 25 mils (.63 cm). Application must be made uniformly to avoid thin spots and care must be taken to avoid pinholes and repair them should they occur.
Step (2) Following an overnight cure, apply ELASTO-DECK™ 5001HT (VOC) at a rate of 100 square feet per gallon (2.45 m²/liter) for a thickness of 16 mils (0.4 mm). It is preferable to use a heavy duty roller for even distribution.
Step (3) Immediately broadcast 1 gallon (3.785 liters) of 20 mesh Monterey sand, or equivalent, uniformly into the wet coating, per 100 sq.ft. (2.45 m²/liter). Assure that the coating is backrolled for even distribution of the sand. Do not broadcast to refusal. Allow to cure overnight.
*Step (4) Repeat Steps 2 and 3, where needed, as advised by the manufacturer. Allow an overnight cure of ELASTO-DECK™ 5001HT (VOC). *For heavy-duty traffic areas.
Step (5) Apply ELASTO-GLAZE™ 6001AL HT (VOC) by roller, brush or spray at 150 sq.ft. per gallon (3.68 m²/liter) to equal 10 mils (0.25mm). Allow 72 hours for complete cure of the system.
Top coat must be the same color as the preceding sand coat.
B. Light duty pedestrian decks.
Step (1) As under A. Allow an overnight cure.
Step (2) Apply ELASTO-GLAZE™ 6001AL HT (VOC) at 100 square feet per gallon (2.45 m²/liter) or 16 (0.4mm) wet mils. Immediately broadcast 1 gallon of 20 mesh Monterey sand, or equivalent, uniformly into the wet coating, per 100 sq.ft (9.29 m²). Assure that the coating is backrolled for even distribution of the sand. Allow an overnight cure before permitting light traffic.

MATERIALS:
Recommended materials and their uses are as follows:
ELASTO-THANE™ 230 is a one part, self-leveling or gungrade, non-staining, polyurethane sealant which cures at ambient temperature to a firm, flexible tear-resistant rubber. It is highly resilient and has excellent recovery characteristics after extended periods of compression or elongation.
ELASTO-POXY™ PRIMER WB: A two-component, solvent based epoxy primer for use on concrete or metal surfaces.
ELASTO-DECK™ 5001HT (VOC) Coating: A one-part, self-leveling, polyurethane coating used as the elastomeric waterproof membrane of the system, and also to lock in the aggregate.
ELASTO-GLAZE™ 6001AL HT (VOC) Coating: A one-part, moisture-cured, aliphatic polyurethane topcoat which protects the ELASTO-DECK™ 5000HT (VOC) from U.V. exposure.
AGGREGATE: 20 mesh Monterey sand or equal, which imparts the slip resistant texture and contributes to wear resistance.

MASTER SPECS:
SECTION 07181: (Word file)
TRAFFIC COATINGS ON PLYWOOD
SECTION 07182: (Word file)
TRAFFIC COATINGS ON CONCRETE
SECTION 07183: (Word file)
TRAFFIC COATINGS, HEAVY DUTY ON CONCRETE
SECTION 07570: (pdf)
TRAFFIC TOPPING

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-THANE™ 230
ELASTO-POXY™ PRIMER PART-A
ELASTO-POXY™ PRIMER PART-B
ELASTO-DECK™ 5001HT (VOC)
ELASTO-GLAZE™ 6001AL HT (VOC)

CATALYSTS:

Super-Cure™ AL
Catalyst for: Cold Weather and/or Low Humidity
Accelerates the tack free time and cure time of:
2) Elasto-Glaze™ 6001AL HT
SUPER-CURE™ AL
SUPER-CURE™ AL

Super-Cure™ Rubber
Catalyst for: Cold Weather and/or Low Humidity
Accelerates the tack free time and cure time of:
3) Elasto-Deck™ 5001HT
SUPER-CURE™ RUBBER
SUPER-CURE™ RUBBER

(Available in 42 colors when coated with Elasto-Glaze™ 6001 AL.)
TECH DATA SHEET | APPLICATION GUIDE | MAINTENANCE MANUAL
AVAILABLE COLOR:

ELASTO-DECK™ 5001 NG is a liquid-applied, single component, aromatic, moisture-cured polyurethane waterproofing membrane, which will not blister or gas. It may be substituted for our standard ELASTO-DECK™ 5001 in all ELASTO-DECK™ 5000 coating systems.

BASIC USES:
ELASTO-DECK™ 5001 NG is a waterproofing membrane used with ELASTO-DECK™ 5000 WDA, ELASTO-DECK™ 5000 X2, ELASTO-DECK™ 5000 TC, ELASTO-DECK™ 5000 MR, ELASTO-DECK™ 5000 PDS, and ELASTO-DECK™ 5000 WS systems. ELASTO-DECK™ 5001 NG may be used to fill minor cracks in concrete, except for expansion joints where ELASTO-THANE™ 227 is recommended. ELASTO-DECK™ 5001 NG may be used to waterproof concrete and plywood decks which are subsequently covered with outdoor carpeting, mortar bed and tile, or wood decking. The product is recommended for all applications which require surface waterproofing, where a bitumen extended polyurethane would not be suitable. ELASTO-DECK™ 5001 NG is also designed as a high performance elastomeric covering over spray applied, polyurethane foam roofs. ELASTO-DECK™ 5001 NG is available in special thixotropic consistency for use over irregular surfaces such as foam roofs. ELASTO-DECK™ 5001 NG must be coated with ELASTO-GLAZE™ 6001 AL if it is used over foam insulated roofs.

SURFACE PREPARATION:
All surfaces which are to be coated with ELASTO-DECK™ 5001 NG must be free of contamination such as curing compounds, concrete hardeners, bond breakers, paint, etc. All surfaces must be dry, having a maximum water content of 20%. Water-curing concrete is recommended instead of using concrete curing compounds. Concrete surfaces should be cleaned by sandblasting, beadblasting or acid etching. Allow a minimum drying time of 72 hours. Except for non-moving shrinkage cracks, and joints must be sealed with ELASTO-THANE™ 230, a single component, moisture-cured sealant manufactured by Pacific Polymers, Inc. All surfaces, except for plywood in good condition, must be primed with DECK-THANE™ PRIMER prior to application of the coating system at a rate of 350 square feet per gallon (8.6 m²/liter).

All seams between plywood sheets and the transition from the metal flashing and the plywood deck must be reinforced by imbedding a 3 inch (7.6 cm) wide strip of glass cloth tape in wet ELASTO-DECK™ 5001 NG, which is brushed evenly over the seam to a width of 4 inches (10 cm) and a thickness of about 20 mils (0.5 mm) wet. The application of ELASTO-DECK™ 5001 NG can subsequently be made immediately over the entire area, including the taped areas. Where ELASTO-DECK™ 5001 NG is used as a protective coating on polyurethane foam roofs, it must be applied within 8 hours from the time the foam is installed.

MSDS DOCUMENTS FOR THIS SYSTEM:
DECK-THANE™ PRIMER
ELASTO-GLAZE™ 6001 AL
ELASTO-DECK™ 5001 NON-GASSING

CATALYSTS:

Super-Cure™ Rubber
Catalyst for: Cold Weather and/or Low Humidity
Accelerates the tack free time and cure time of:
2) Elasto-Deck™ 5001 Non-Gassing
SUPER-CURE™ RUBBER
SUPER-CURE™ RUBBER

Splattercoat parking deck system with an anti-skid finish in 42 colors for parking, roofs, helicopter pads, and stadium floors. (70 Dry Mil Average Thickness)
TECH DATA SHEET | APPLICATION GUIDE | MAINTENANCE MANUAL
AVAILABLE COLORS:

A liquid-applied, single-component, moisture-cured, elastomeric traffic coating system for waterproofing parking decks, roofs, helicopter pads, stadium floors, etc., based on polyurethane elastomers. The ELASTO-DECK™ 5000 PDS system consists of DECK-THANE™ PRIMER, ELASTO-DECK™ 5001 base coat, ELASTO-GLAZE™ 6001 AL top coat, and ELASTO-GLAZE™ 6001 AL SPLATTERCOAT, applied using suitable spray equipment.
Except for non-moving shrinkage cracks, all other cracks and joints must be sealed with ELASTO-THANE™ 230. All surfaces must be primed with DECK-THANE™ PRIMER.

BASIC USES:
For waterproofing parking decks, roofs, helicopter pads, stadium floors, etc. Designed to withstand vehicular traffic. Anti-skid textured finish.

SURFACE PREPARATION:
All concrete surfaces which are to receive ELASTO-DECK™ 5000 PDS shall be free of contamination such as water, curing compounds, hardeners, bond-breakers, paint, etc. A light broom-finish is recommended for concrete surfaces. It is desirable to watercure concrete in lieu of curing compounds. Contaminants should be removed by sandblasting or acid-etching. If acid-etching is performed, properly neutralize the acid, followed by thorough rinsing of the concrete. Allow adequate time for surface to dry. Except for non-moving shrinkage cracks, all other cracks and joints must be sealed with ELASTO-THANE™ 230, a single-component, moisture-cured sealant manufactured by Pacific Polymers, Inc. All concrete surfaces must be primed with DECK-THANE™ PRIMER prior to application of the coating system at a rate of 305-350 square feet per gallon (7.35-8.58 m²/liter).

APPLICATION:
ELASTO-DECK™ 5001 shall be applied to the primed concrete at a rate of 56 square feet per gallon (1.47 m²/liter) per coat resulting in a 25 dry mil thickness (0.625 mm). After a 24-hour cure, another coat of ELASTO-DECK™ 5001 is applied at the same 25 mil (0.625 mm) thickness for a total dry film thickness of 50 mils (1.25 mm).
After a 24 hour cure apply ELASTO-GLAZE™ 6001 AL at a rate of 120 sq. ft. per gallon (2.82 m²/liter), for a 10 dry mil thickness (0.25 mm). Allow this coating to cure for 24 hours after which ELASTO-GLAZE™ 6001 SPLATTERCOAT is applied using suitable spray equipment at a coverage of 105 sq. ft. per gallon (2.45 m²/liter) resulting in a uniformly textured finish with an average thickness of 10 dry mils. Do not allow the ELASTO-GLAZE™ 6001 AL to cure longer than 24 hours, otherwise sanding and recoating may be required.
A #20 mesh aggregate is to be broadcast into the wet splatter coat, for anti-skid purposes. Do not use silica sand. The completed deck coating system must be allowed to cure for at least 72 hours prior to admitting vehicular traffic.

MASTER SPECS:
SECTION 07570: (pdf)
TRAFFIC TOPPING

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-THANE™ 230
DECK-THANE™ PRIMER
ELASTO-DECK™ 5001
ELASTO-GLAZE™ 6001 AL
ELASTO-GLAZE™ 6001AL SPLATTER-COAT

CATALYSTS:

Super-Cure™ AL
Catalyst for: Cold Weather and/or Low Humidity
Accelerates the tack free time and cure time of:
1) Elasto-Glaze™ 6001AL
SUPER-CURE™ AL
SUPER-CURE™ AL

Super-Cure™ Rubber
Catalyst for: Cold Weather and/or Low Humidity
Accelerates the tack free time and cure time of:
1) Elasto-Deck™ 5001
SUPER-CURE™ RUBBER
SUPER-CURE™ RUBBER

Polyurethane Walking Deck Coating for decks, balconies, and plazas, available in a natural aggregate or a pigmented finish in 42 colors.
TECH DATA SHEET | APPLICATION GUIDE | MAINTENANCE MANUAL
AVAILABLE COLORS:

A liquid-applied, single-component, moisture-cured, elastomeric coating system for foot traffic, such as walking decks, balconies, plazas, etc. The complete system is skid-resistant with a textured finish, and approximately 1/8" thick (3 mm), including aggregate. The system consists of ELASTO-DECK™ 5001 base coat, ELASTO-GLAZE™ 6001 AL topcoat and primer where necessary. Except for non-moving shrinkage cracks, all other cracks and joints must be sealed with ELASTO-THANE™ 230. All surfaces, where necessary, must be primed with DECK-THANE™ PRIMER.

BASIC USES
For waterproofing walking decks, balconies, plazas, etc. Designed for foot traffic. Skid-resistant, textured finish. The complete system is approximately 1/8" thick (3 mm), inclusive of aggregate.

SURFACE PREPARATION:
All surfaces which are to receive ELASTO-DECK™ 5000 WDA shall be free of contamination such as water, curing compounds, hardeners, bond-breakers, paint, etc. A light broom-finish is recommended for concrete surfaces. It is desirable to watercure concrete in lieu of curing compounds. Contaminants should be removed by sandblasting or acid-etching. If etching is used, allow adequate time for surface to dry. Except for non-moving shrinkage cracks, all other cracks and joints must be sealed with ELASTO-THANE™ 230, a single-component, moisture-cured sealant manufactured by Pacific Polymers, Inc. All surfaces, where necessary, must be primed with DECK-THANE™ PRIMER prior to application of the coating system at a rate of 350 square feet per gallon (8.6 m²/liter), except for plywood in good condition. All seams between plywood sheets and those between metal flashing and the plywood deck must be reinforced by imbedding a 2-inch wide (5 cm) strip of glass cloth tape in wet ELASTO-DECK™ 5001, which is brushed evenly over the seam in a width of about 3 inches (7.6 cm) and a thickness of about 30 mils wet (0.76 mm). The application of ELASTO-DECK™ 5001 can subsequently be made immediately over the entire area, including the taped areas. Cracks in concrete must be treated in the same way.

APPLICATION:
ELASTO-DECK™ 5001 shall be applied to the primed concrete or plywood at a rate of 45 square feet per gallon (1.1 m²/liter) resulting in a 30 dry mil thickness (.76 mm). After a 24-hour cure, apply ELASTO-GLAZE™ 6001 AL PIGMENTED, at a rate of 115 square feet per gallon (2.8 m²/liter). Broadcast desired aggregate into the wet coating until refusal. After an overnight cure, sweep or blow off all the loose aggregate and apply another coat of ELASTO-GLAZE™ 6001 AL pigmented or clear, at a coverage of 115 square feet per gallon. Allow 48 hours cure time before allowing heavy pedestrian traffic onto the finished system.

MASTER SPECS:
SECTION 07181: (Word file)
TRAFFIC COATINGS ON PLYWOOD
SECTION 07182: (Word file)
TRAFFIC COATINGS ON CONCRETE
SECTION 07183: (Word file)
TRAFFIC COATINGS, HEAVY DUTY ON CONCRETE
SECTION 07570: (pdf)
TRAFFIC TOPPING

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-THANE™ 230
DECK-THANE™ PRIMER
ELASTO-DECK™ 5001
ELASTO-GLAZE™ 6001 AL

CATALYSTS:

Super-Cure™ AL
Catalyst for: Cold Weather and/or Low Humidity
Accelerates the tack free time and cure time of:
1) Elasto-Glaze™ 6001AL
SUPER-CURE™ AL
SUPER-CURE™ AL

Super-Cure™ Rubber
Catalyst for: Cold Weather and/or Low Humidity
Accelerates the tack free time and cure time of:
1) Elasto-Deck™ 5001
SUPER-CURE™ RUBBER
SUPER-CURE™ RUBBER

Parking Deck System with Metal Grit Non-Skid Finish in 42 colors for waterproofing parking decks, roofs, and stadiums.
TECH DATA SHEET | PRODUCT BULLETIN
APPLICATION GUIDE | MAINTENANCE MANUAL
AVAILABLE COLORS:

A liquid-applied, single-component, moisture-cured, elastomeric coating system for parking decks based on polyurethane elastomers. The ELASTO-DECK™ 5000 TC system consists of a primer, ELASTO-DECK™ 5001 base coat, ELASTO-GLAZE™ 6001 AL top coat with aluminum oxide or silicone carbide grit. The ELASTO-DECK™ 5000 TC system is used for waterproofing parking decks, roofs, stadium floors, etc. It is designed for vehicular traffic. It has an anti-skid textured finish. Except for non-moving shrinkage cracks, all other cracks and joints must be sealed with ELASTO-THANE™ 230. All surfaces must be primed with DECK-THANE™ PRIMER.

BASIC USES:
The ELASTO-DECK™ 5000 TC system is used for waterproofing parking decks, roofs, stadium floors, etc. Designed for vehicular traffic. Anti-skid textured finish.

APPLICATION:
A. Parking and Pedestrian Areas:
1a. Base Coat: Apply ELASTO-DECK™ 5001 at the rate of 55 sq. ft. per gallon (1.23 m²/liter) to produce a 25 mil dry (.6mm) film thickness. Coating may be installed with squeegee and backroll or spray. (See Note #1)
2a. Top Coat: Apply ELASTO-GLAZE™ 6001 at the rate of 80 sq. ft. per gallon (1.84 m²/liter) to produce a 15 mil dry (.38mm) film thickness. Coating may be applied by squeegee or spray. While coating is in a fluid condition, broadcast 20-24 mesh silicon carbide or aluminum oxide grit at the rate of 5-6 lbs./100 sq. ft. and backroll to ensure even distribution of the grit. (See Note #2)
B. Traffic Aisles:
1b. Base Coat: Apply ELASTO-DECK™ 5001 at the rate of 45 sq. ft. per gallon (0.98-1.1 m²/liter) to produce a 30 mil dry (.76mm) film thickness. Coating may be applied by squeegee and backroll or spray. (See Note #1)
2b. Top Coat #1: Apply ELASTO-GLAZE™ 6001 AL at the rate of 120 sq. ft. per gallon (2.8 m²/liter) to produce a 10 mil dry (0.25mm) film thickness. (See Note #3) Coating may be applied by squeegee and backroll or spray. While coating is in a fluid condition, broadcast #20-24 mesh silicone carbide or aluminum oxide at the rate of refusal (completely bury top coat in grit). Allow to cure overnight and carefully remove excess grit.
3b. Top Coat #2: Apply ELASTO-GLAZE™ 6001 AL at the rate of 120 sq. ft. per gallon (2.8 m²/liter) to produce a 10 mil (0.25mm) dry film thickness. Coating may be applied by spray or roller. Thinning of the coating material is not permitted for application purposes. Regardless of how applied, coating shall be backrolled to provide an even and consistently thick finish coat. (See Note #2)
Application NOTES:
Note #1: Allow ELASTO-DECK™ 5001 to cure 16 hours minimum. At temperatures less than 75° F (24 deg. C) and/or relative humidity less than 50%, will decrease the curing time.
Note #2: Allow ELASTO-GLAZE™ 6001 to cure 16 hours minimum. At temperatures less than 75° F (24 deg. C) and/or humidity less than 50%, extend curing time before allowing any traffic. At least 72 hours total cure time should elapse before admitting vehicular traffic.
Note #3: In the turning radius, ramps, entrances, exits and other very high wear traffic areas, it is advisable to apply the ELASTO-GLAZE™ 6001 AL Top Coat #1 (Broadcast Coat) at a rate of 80 sq. ft. per gallon (1.84 m²/liter) for a 15 dry mil (0.38mm) thickness.

MASTER SPECS:
SECTION 07181: (Word file)
TRAFFIC COATINGS ON PLYWOOD
SECTION 07182: (Word file)
TRAFFIC COATINGS ON CONCRETE
SECTION 07183: (Word file)
TRAFFIC COATINGS, HEAVY DUTY ON CONCRETE
SECTION 07570: (pdf)
TRAFFIC TOPPING

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-THANE™ 230
DECK-THANE™ PRIMER
ELASTO-DECK™ 5001
ELASTO-GLAZE™ 6001 AL

CATALYSTS:

Super-Cure™ AL
Catalyst for: Cold Weather and/or Low Humidity
Accelerates the tack free time and cure time of:
1) Elasto-Glaze™ 6001AL
SUPER-CURE™ AL
SUPER-CURE™ AL

Super-Cure™ Rubber
Catalyst for: Cold Weather and/or Low Humidity
Accelerates the tack free time and cure time of:
1) Elasto-Deck™ 5001
SUPER-CURE™ RUBBER
SUPER-CURE™ RUBBER

Pedestrian and Vehicular Deck Coating - Polyurea with user-controlled consistency, shore hardness, and thickness that tolerates extreme movement and harsh environments.
TECH DATA SHEET | MAINTENANCE MANUAL
AVAILABLE COLORS:

A liquid applied, two component, fast curing, 100% solids polyurea coating, applied by special spray equipment, which forms an exceptionally durable finish. ELASTO-DECK™ 8000 coating is a plural component, 100% solid, spray-applied elastomer and is available in an aromatic or aliphatic version. The product is available as a soft, stretch elastomer to a tough, hard elastomer. The coating is dry to the touch in 1 second. It can be applied in any thickness, on horizontal or vertical surfaces.
Perhaps the greatest advantage of this system is its inherent “stress relaxation,” which makes it uniquely suited to bridge cracks. When stretched out, this coating does not recover instantly as do all urethanes, but instead relaxes, thereby removing stress on the material and on the bond line. This feature prevents splitting of the coating over cracks.

BASIC USES:
ELASTO-DECK™ 8000 coating is designed to be spray applied on concrete, metal and wood structures for exterior and interior applications that require waterproofing, specific chemical resistance, corrosion and abrasion protection.
Roofing: ELASTO-DECK™ 8000 in the aliphatic version is an elastomeric coating for roofs and helipads where an absolutely waterproof coating is crucial, above living quarters and any other occupied areas. ELASTO-DECK™ 8000 is not only limited to new construction but can be used to rehabilitate old, existing built-up, or cap sheet roofs that failed or need repairs. Because of its tenacious bond to most substrates, ELASTO-DECK™ 8000 can be applied directly to the existing roof system. This will help save the extreme costs of removing a built-up roof system.
Traffic Bearing Coating: ELASTO-DECK™ 8000 can be used as a traffic bearing system, either pedestrian or vehicular traffic. Due to excellent tensile strength and abrasion resistance of ELASTO-DECK™ 8000 as well as availability of a wide range of Shore Hardnesses, it allows the system to be designed to tolerate movement and extreme conditions where other coatings typically fail. When used as a traffic bearing coating, the ELASTO-DECK™ 8000 may require a primer. ELASTO-DECK™ 8000 coating can be applied with an anti-skid surface, which is obtained by holding the spray gun farther from the surface, texture is created by the “in flight” curing of this extremely fast curing elastomer. The sprayed particles of the liquid elastomers do not level out when they hit the deck, thus creating this elastomeric, non-skid texture.
ELASTO-DECK™ 8000 coating has certain uses besides waterproofing, such as:

1. Protective coatings and linings, such as truckbody liners.
2. Abrasion-resistant coatings.
3. Pipe coatings.
4. Soil stabilization.
5. Construction coatings.
6. Grouting.
7. Encapsulation — asbestos, concrete walls, drywall, etc.
8. Highway stripping.
9. Wire bundlings.
10. Industrial coatings.
11. Highway and bridge overlays.
12. Drilling platforms.
13. Tank coatings for non-potable water or hydrocarbon storage.

ADVANTAGES: The Aliphatic coating has:

1. Long term stability toward UV light, enabling them to be used in a variety of outdoor applications.
2. The coating gels within 1-3 seconds after mixing, dries in about 10 seconds and allows traffic within one hour.
3. The sprayed coating is affected very little by weather variations, i.e. rain, high humidity, heat, cold, etc.
4. One coat systems can be sprayed thus reducing time and labor.
5. The coating has excellent physical properties, including tensile strength, elongation and abrasion resistance.
6. High thermal stability at temperatures up to 350°F.
7. Can be sprayed or sloped on vertical surfaces without forming drips or runs.
8. Ease of application. Can be sprayed with commercially available spray application equipment. Little maintenance toward equipment and spray gun.

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-DECK™ 8000 PART-A
ELASTO-DECK™ 8000 PART-B

Water-cured, polyurethane sloping system using an elastomeric binder adhesive mixed with aggregate for sloping decks and ponding areas.
TECH DATA SHEET
AVAILABLE COLOR:

A Liquid-applied, single-component, water-cured, polyurethane binder adhesive. The ELASTO-GRADE™ System consists of ELASTO-GRADE™ binder adhesive, 50/50 blend of #0 & #1 sand, and a primer where necessary.

BASIC USES:
ELASTO-GRADE™ is designed for sloping flat decks and ponding areas. Designed for use under the ELASTO-DECK™ 5000 Deck Coating Systems.

SURFACE PREPARATION:
All surfaces that are to receive ELASTO-GRADE™ shall be free of contamination such as water, curing compounds, paints, bond-breakers, hardeners and existing coatings. Except for non-moving shrinkage cracks, all other cracks and joints must be sealed with ELASTO-THANE™ 230, a single-component, moisture-cured sealant manufactured by PACIFIC POLYMERS, INC. All surfaces, where necessary, must be primed with ELASTO-POXY™ PRIMER prior to application of the sloping material at a rate of 300 square feet per gallon, except for plywood in good condition.

APPLICATION:
Prior to application, ELASTO-GRADE™ binder is mixed with 10% water using a jiffy mixer at low R.P.M.'s and then is mixed with a 50/50 blend of #0 & #1 sand. Blend for 3-5 minutes. The mixing ratio is 1 part ELASTO-GRADE™ binder to 3 parts sand. ELASTO-GRADE™ shall be applied to the primed (if necessary) surface with a 1/4" notch trowel, use downward pressure, distribute material to desired thickness or slope. Use a smooth trowel to finish profile of slope. Generally 24 hours is required to allow material to cure, although cure times will vary depending thickness.

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-THANE™ 230
ELASTO-POXY™ PRIMER PART-A
ELASTO-POXY™ PRIMER PART-B
ELASTO-GRADE™ BINDER

Fiberglass reinforced water based Acrylic Deck System for walking decks, balconies, patios, etc., where the surface must be accessible for foot traffic the same day.
TECH DATA SHEET | CASE STUDY | MAINTENANCE MANUAL
AVAILABLE COLORS:

A wear resistant coating for new skidproof decks, as well as old damaged or cracked surfaces. A Liquid applied, single-component, acrylic deck covering system. The system consists of FIBERGLASS MAT saturated with ELASTO-TEX™ BASE COAT by roller, sprayed with ELASTO-TEX™ TEXTURE COAT, followed by ELASTO-TEX™ TOP COAT applied by roller. Conforms to all known V.O.C. requirements in the State of California.

BASIC USES:
For waterproofing areas such as patios, sundecks, stairways, balconies,etc. ELASTO-TEX™ DECK COATING can be used in situations where a skidproof, wear resistant surface is required. It may be used on new decks as well as old concrete decks which are damaged or cracked. The system is suitable for exterior applications where a deck surface must be accessible for foot traffic the same day such as retrofit work. ELASTO-TEX™ DECK COATING can be used in situations where a skidproof, wear resistant surface is required, on new decks as well as old concrete decks which are damaged or cracked. The complete system is approximately 3/16" (4.8mm) thick.

APPLICATION:
Cover all areas to receive ELASTO-TEX™ DECK COATING with fiberglass mat butting edges together without overlapping the mat. Overapplying the fiberglass mat will result in unsightly seams in the finished system. Saturate the fiberglass thoroughly with the ELASTO-TEX™ BASE COAT at the rate of 50 sq. ft. per gallon (1.2 m²/liter), by applying with a roller, adhering the system to the substrate. Allow to cure a minimum of 2-3 hours based at 77°F (25°C). Apply ELASTO-TEX™ TEXTURE COAT by spraying at the rate of 75-100 sq. ft. per gallon (1.8-2.4 m²/liter). Different size textures can be applied by adjusting the hopper gun. Allow texture coat to cure approximately 2-3 hours. Apply ELASTO-TEX™ TOP COAT by roller at the rate of 100 sq. ft. per gallon (2.4 m²/liter). Allow 2-3 hours prior to allowing light foot traffic and 72 hours before allowing heavy traffic.

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-TEX™ PRIMER
ELASTO-TEX™ CAULK
ELASTO-TEX™ DECK COATING

Beautiful slip-resistant waterproofing for traffic and walking decks and resilient cushioned sanitary flooring for hospitals and convalescent facilities, suitable for all climates.
One Day Elastomeric Surfacing Systems:

• Group A: Slip Resistant Waterproof Traffic Coatings
• Group B: Resilient Waterproof Flooring
• Group C: Slip Resistant Waterproof Pedestrian Traffic Coatings

TECH DATA SHEET | MAINTENANCE MANUAL
AVAILABLE COLORS:

A Liquid applied, single component, water-cured, low odor polyurethane deck covering systems designed to be applied in one day with the use of Super Cure. Since the RAPID-FLEX™ systems are water-cured, these materials do not need atmospheric moisture to cure. The RAPID-FLEX™ materials are non-gassing, which enables the applicator to apply these materials in any thickness without the problems of gassing or foaming. With these systems, the use of different slip resistant aggregates allows the specifier to offer a variety of textures, the most popular of which is PACPOLY-FLEX™ RUBBER GRANULES. These granules have the ability to move and flex which provides a soft, silky, resilient texture that is not abrasive like other aggregates. The use of rubber granules as an aggregate is beneficial on patios, decking around the house, pool decks and play areas because they will not cut or tear the knees, hands or the bottom of feet. Vehicular traffic decks, and certain pedestrian traffic decks, require a much harder slip resistant, such as sand or aluminum oxide. These systems are comprised of a combination of the following components:

• RAPID-FLEX™ HT
• RAPID-FLEX™ HT 100% SOLIDS
• RAPID-FLEX™ AR
• RAPID-FLEX™ AL
• PACPOLY-FLEX™ RUBBER GRANULES
• SUPER CURE

BASIC USES:
RAPID-FLEX™ Systems are designed for rapid, one-day (in most conditions) installations over properly prepared concrete or plywood substrates to create a monolithic, waterproof, durable, elastomeric and slip resistant (when necessary) surface. RAPID-FLEX™ is designed to protect and beautify a wide range of applications. The system retains its elastomeric qualities in all climates including areas that are subjected to heavy freeze/thaw cycles. This system will not only ensure complete waterproofing and added protection, it will greatly increase the longevity and aesthetic value of the structure it is used on. Different areas of application require different types of slip resistant aggregate or no aggregate at all.

Slip Resistant Traffic Coatings utilizing the RAPID-FLEX™ components, can be used anywhere conventional deck coating systems are now used, taking advantage of the fast cure and non-gassing features that they offer. The Resilient Flooring Systems fulfill a great need in retirement homes, hospitals, and convalescent facilities, to prevent injury to persons when falling. At a 1/4 inch thick, such systems absorb impact and cushion a fall enormously. Instances where employees stand on their feet for long periods while performing their jobs, will benefit from RAPID-FLEX™ resilient flooring, replacing rubber mats with a truly seamless resilient surface with outstanding sanitary features. The Pedestrian Traffic Coatings provide quickly installed, economical, yet beautiful and functional, waterproof walking decks.

MSDS DOCUMENTS FOR THIS SYSTEM:
RAPID-FLEX™-AL
RAPID-FLEX™-AR
RAPID-FLEX™-HT
RAPID-FLEX™-WB PART-A
RAPID-FLEX™-WB PART-B

CATALYSTS:

Super-Cure™ AL
Catalyst for: Cold Weather and/or Low Humidity
Accelerates the tack free time and cure time of:
3) Rapid-Flex™ AL
SUPER-CURE™ AL
SUPER-CURE™ AL

Super-Cure™ AR
Catalyst for: Cold Weather and/or Low Humidity
Accelerates the tack free time and cure time of:
2) Rapid-Flex™ AR
SUPER-CURE™ AR
SUPER-CURE™ AR

Super-Cure™ Rubber
Catalyst for: Cold Weather and/or Low Humidity
Accelerates the tack free time and cure time of:
6) Rapid-Flex™ HT
SUPER-CURE™ RUBBER
SUPER-CURE™ RUBBER

A siloxane penetrating sealer with 20% solids for use on masonry surfaces to provide protection from moisture which results in alkali, efflorescence, freeze/thaw scaling, salt penetration, mold and mildew formations.
TECH DATA SHEET
AVAILABLE COLOR:

AQUA-GUARD™ 20's molecular structure allows exceptional penetration which provides extended life of the material. When a surface is properly treated with AQUA-GUARD™ 20, there is no apparent surface film, and the natural look, color or texture does not alter appreciably.

BASIC USES:
AQUA-GUARD™ 20 produces a chemical bond with the masonry's natural materials which will retain its natural vapor permeability. Recommended surfaces for AQUA-GUARD™ 20 are: Architectural Block, Architectural Concrete, Brick Pavers, Concrete Block, Concrete Monuments, Natural Stones, Precast Concrete, Poured in Place Concrete, Marble, Terrazzo, Travertine, etc. Also suitable for use on integrally colored concrete.

SURFACE PREPARATION:
Prior to application, all areas to be treated with AQUA-GUARD™ 20 must be free of any contamination such as waxes, oils, loose concrete, dirt, curing compounds or any other substance that might make penetration of the surface difficult. Before application, make sure all surface areas are properly prepared. The best method of removing contaminants is mechanically, however, detergents and chemicals often will remove contaminants from the substrate and open the pores of the substrate. On-site testing is recommended to determine the best method of cleaning. Mechanically removing contamination from the concrete may be done by sandblasting, scarifying, metallic abrasive blasting or water blasting. When using the option of mechanically removing contamination, you must take into consideration that it may damage the surface that is to be sealed with AQUA-GUARD™ 20 resulting in a very uneven appearance. For new concrete, allow the concrete to cure for a minimum of 21 days before applying AQUA-GUARD™ 20.

COVERAGE RATES:
(Coverage rates are estimated due to the different textures of finishes.)
Natural Stone (Smooth) 100-150 sq.ft./gal (2.45-3.68m²/liter)
Natural Stone (Rock Face Cut) 100-150 sq.ft./gal (2.45-3.68m²/liter)
Stucco 100-150 sq.ft./gal (2.45-3.68m²/liter)
Concrete Blocks 100-150 sq.ft./gal (2.45-3.68m²/liter)
Precast Concrete 125-175 sq.ft./gal (3.07-4.30m²/liter)
Rock Face Concrete 150-200 sq.ft./gal (3.68-4.91m²/liter)
Concrete Block 60-80 sq.ft./gal (1.47-1.96m²/liter)
Cement Brick 80-120 sq.ft./gal (1.96-2.94m²/liter)
Exposed Aggregate 100-150 sq.ft./gal (2.45-3.68m²/liter)
Brick Pavers, Tile 125-175 sq.ft./gal (3.07-4.30m²/liter)
Concrete (Broom Finished) 100-125 sq.ft./gal (2.45-3.07m²/liter)
Concrete (Porous) 70-110 sq.ft./gal (1.71-2.70m²/liter)
Marble 150-200 sq.ft./gal (3.68-4.91m²/liter)
Terrazzo 150-200 sq.ft./gal (3.68-4.91m²/liter)
Travertine 150-200 sq.ft./gal (3.68-4.91m²/liter)

MSDS DOCUMENTS FOR THIS SYSTEM:
AQUA-GUARD™ 20

A water-based siloxane penetrating sealer with 20% solids for use on masonry surfaces to provide protection from moisture which results in alkali, efflorescence, freeze/thaw scaling, salt penetration, mold and mildew formations.
TECH DATA SHEET
AVAILABLE COLOR:

AQUA-GUARD™ 20WB's molecular structure allows exceptional penetration which provides extended life of the material. When a surface is properly treated with AQUA-GUARD™ 20WB, there is no apparent surface film, and the natural look, color or texture does not alter appreciably.

BASIC USES:
AQUA-GUARD™ 20WB produces a chemical bond with the masonry's natural materials which will retain its natural vapor permeability. Recommended surfaces for AQUA-GUARD™ 20WB are: Architectural Block, Architectural Concrete, Brick Pavers, Concrete Block, Concrete Monuments, Natural Stones, Precast Concrete, Poured in Place Concrete, Marble, Terrazzo, Travertine, etc. Also suitable for use on integrally colored concrete.

SURFACE PREPARATION:
Prior to application, all areas to be treated with AQUA-GUARD™ 20WB must be free of any contamination such as waxes, oils, loose concrete, dirt, curing compounds or any other substance that might make penetration of the surface difficult. Before application, make sure all surface areas are properly prepared. The best method of removing contaminants is mechanically, however, detergents and chemicals often will remove contaminants from the substrate and open the pores of the substrate. On-site testing is recommended to determine the best method of cleaning. Mechanically removing contamination from the concrete may be done by sandblasting, scarifying, metallic abrasive blasting or water blasting. When using the option of mechanically removing contamination, you must take into consideration that it may damage the surface that is to be sealed with AQUA-GUARD™ 20WB resulting in a very uneven appearance. For new concrete, allow the concrete to cure for a minimum of 21 days before applying AQUA-GUARD™ 20WB.

COVERAGE RATES:
(Coverage rates are estimated due to the different textures of finishes.)
Natural Stone (Smooth) 100-150 sq.ft./gal (2.45-3.68m²/liter)
Natural Stone (Rock Face Cut) 100-150 sq.ft./gal (2.45-3.68m²/liter)
Stucco 100-150 sq.ft./gal (2.45-3.68m²/liter)
Concrete Blocks 100-150 sq.ft./gal (2.45-3.68m²/liter)
Precast Concrete 125-175 sq.ft./gal (3.07-4.30m²/liter)
Rock Face Concrete 150-200 sq.ft./gal (3.68-4.91m²/liter)
Concrete Block 60-80 sq.ft./gal (1.47-1.96m²/liter)
Cement Brick 80-120 sq.ft./gal (1.96-2.94m²/liter)
Exposed Aggregate 100-150 sq.ft./gal (2.45-3.68m²/liter)
Brick Pavers, Tile 125-175 sq.ft./gal (3.07-4.30m²/liter)
Concrete (Broom Finished) 100-125 sq.ft./gal (2.45-3.07m²/liter)
Concrete (Porous) 70-110 sq.ft./gal (1.71-2.70m²/liter)
Marble 150-200 sq.ft./gal (3.68-4.91m²/liter)
Terrazzo 150-200 sq.ft./gal (3.68-4.91m²/liter)
Travertine 150-200 sq.ft./gal (3.68-4.91m²/liter)

MSDS DOCUMENTS FOR THIS SYSTEM:
AQUA-GUARD™ 20WB

A siloxane penetrating sealer with 40% solids for use on masonry surfaces to provide protection from moisture which results in alkali, efflorescence, freeze/thaw scaling, salt penetration, mold and mildew formations.
TECH DATA SHEET
AVAILABLE COLOR:

AQUA-GUARD™ 40's molecular structure allows exceptional penetration which provides extended life of the material. When a surface is properly treated with AQUA-GUARD™ 40, there is no apparent surface film, and the natural look, color or texture does not alter appreciably.

BASIC USES:
AQUA-GUARD™ 40 produces a chemical bond with the masonry's natural materials which will retain its natural vapor permeability. Recommended surfaces for AQUA-GUARD™ 40 are: Architectural Block, Architectural Concrete, Brick Pavers, Concrete Block, Concrete Monuments, Natural Stones, Precast Concrete, Poured in Place Concrete, Marble, Terrazzo, Travertine, etc. Also suitable for use on integrally colored concrete.

SURFACE PREPARATION:
Prior to application, all areas to be treated with AQUA-GUARD™ 40 must be free of any contamination such as waxes, oils, loose concrete, dirt, curing compounds or any other substance that might make penetration of the surface difficult. Before application, make sure all surface areas are properly prepared. The best method of removing contaminants is mechanically, however, detergents and chemicals often will remove contaminants from the substrate and open the pores of the substrate. On-site testing is recommended to determine the best method of cleaning. Mechanically removing contamination from the concrete may be done by sandblasting, scarifying, metallic abrasive blasting or water blasting. When using the option of mechanically removing contamination, you must take into consideration that it may damage the surface that is to be sealed with AQUA-GUARD™ 40 resulting in a very uneven appearance. For new concrete, allow the concrete to cure for a minimum of 21 days before applying AQUA-GUARD™ 40.

COVERAGE RATES:
(Coverage rates are estimated due to the different textures of finishes.)
Natural Stone (Smooth) 100-150 sq.ft./gal (2.45-3.68m²/liter)
Natural Stone (Rock Face Cut) 100-150 sq.ft./gal (2.45-3.68m²/liter)
Stucco 100-150 sq.ft./gal (2.45-3.68m²/liter)
Concrete Blocks 100-150 sq.ft./gal (2.45-3.68m²/liter)
Precast Concrete 125-175 sq.ft./gal (3.07-4.30m²/liter)
Rock Face Concrete 150-200 sq.ft./gal (3.68-4.91m²/liter)
Concrete Block 60-80 sq.ft./gal (1.47-1.96m²/liter)
Cement Brick 80-120 sq.ft./gal (1.96-2.94m²/liter)
Exposed Aggregate 100-150 sq.ft./gal (2.45-3.68m²/liter)
Brick Pavers, Tile 125-175 sq.ft./gal (3.07-4.30m²/liter)
Concrete (Broom Finished) 100-125 sq.ft./gal (2.45-3.07m²/liter)
Concrete (Porous) 70-110 sq.ft./gal (1.71-2.70m²/liter)
Marble 150-200 sq.ft./gal (3.68-4.91m²/liter)
Terrazzo 150-200 sq.ft./gal (3.68-4.91m²/liter)
Travertine 150-200 sq.ft./gal (3.68-4.91m²/liter)

MSDS DOCUMENTS FOR THIS SYSTEM:
AQUA-GUARD™ 40

A seamless, elastomeric, waterproof coating for use on concrete and masonry exterior walls to protect against water penetration, and to provide an aesthetic improvement to those structures.
TECH DATA SHEET
AVAILABLE COLOR:

An elastomeric, waterbased acrylic coating. Contains no plasticizers; chemically modified to provide truly elastomeric qualities. ELASTO-TEX™ WALLCOATING is a highly durable, flexible coating with outstanding resistance to weathering, ultra-violet light, mildew and water. (It is a breathing type coating allowing water vapor to escape from the interior without loss of adhesion).

BASIC USES:
The coating will waterproof porous structures, such as, exterior concrete and masonry walls and wood siding,as well as seal hairline cracks, caused by the settling of the building or earthquake. The product is to be used only on above grade walls.

SURFACE PREPARATION:
Concrete should be cured for at least 28 days prior to coating. All concrete and masonry surfaces shall be thoroughly cleaned to remove all dirt, grease, efflorescence or other foreign matter. ELASTO-TEX™ WALLCOATING will bond to painted surfaces, but it must be understood that such a system will bond only as well as the paint is bonded to the substrate. Wood surfaces must be cleaned and relatively dry before application. All cracks over 1/16" (1.6 mm) in width must be ground and caulked flush with ELASTO-TEX™ CAULK.

APPLICATION:
Certain surfaces, such as extremely porous masonry concrete or wood, may require ELASTO-TEX™ primer. This primer must be applied at 200-300 sq. ft. per gallon depending on the porosity of the substrate. The ELASTO-TEX™ WALLCOATING coating may be applied after a 1 hour dry time. ELASTO-TEX™ WALLCOATING is applied at 60-100 sq. ft. per gallon depending on the surface, yielding 10 dry mils (.25 mm). Two coats or more at this coverage are recommended following a 24 hour cure time between coats. Apply in a cross pattern to eliminate pin holes. Application may be made by brush, roller or spray. Airless spray equipment or conventional heavy-duty spray equipment works well. ELASTO-TEX™ WALLCOATING is thixotropic rather than viscous and, therefore, breaks up easily in a spray pattern. The first coat must be thoroughly dry before applying a second coat. The time required will vary depending on temperature, wind and humidity. All ferrous surfaces should be primed with a rust inhibiting primer prior to application of ELASTO-TEX™ WALLCOATING. Equipment may be cleaned up with soap and water.

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-TEX™ PRIMER
ELASTO-TEX™ CAULK
ELASTO-TEX™ WALLCOATING

A seamless, elastomeric, high shore waterproof coating for use on concrete and masonry exterior walls to protect against water penetration, and to provide an aesthetic improvement to those structures.
TECH DATA SHEET
AVAILABLE COLORS:

Concrete Gray	Beige	Tan	White	Off-White	Custom Colors Available

An elastomeric, waterbased acrylic coating. Contains no plasticizers; chemically modified to provide truly elastomeric qualities. ELASTO-TEX™ WALLCOATING HS is a highly durable, flexible coating with outstanding resistance to weathering, ultra-violet light, mildew and water. (It is a breathing type coating allowing water vapor to escape from the interior without loss of adhesion).

BASIC USES:
The coating will waterproof porous structures, such as, exterior concrete and masonry walls and wood siding,as well as seal hairline cracks, caused by the settling of the building or earthquake. The product is to be used only on above grade walls.

SURFACE PREPARATION:
Concrete should be cured for at least 28 days prior to coating. All concrete and masonry surfaces shall be thoroughly cleaned to remove all dirt, grease, efflorescence or other foreign matter. ELASTO-TEX™ WALLCOATING HS will bond to painted surfaces, but it must be understood that such a system will bond only as well as the paint is bonded to the substrate. Wood surfaces must be cleaned and relatively dry before application. All cracks over 1/16" (1.6 mm) in width must be ground and caulked flush with ELASTO-TEX™ CAULK.

APPLICATION:
Certain surfaces, such as extremely porous masonry concrete or wood, may require ELASTO-TEX™ primer. This primer must be applied at 200-300 sq. ft. per gallon depending on the porosity of the substrate. The ELASTO-TEX™ WALLCOATING HS coating may be applied after a 1 hour dry time. ELASTO-TEX™ WALLCOATING HS is applied at 60-100 sq. ft. per gallon depending on the surface, yielding 10 dry mils (.25 mm). Two coats or more at this coverage are recommended following a 24 hour cure time between coats. Apply in a cross pattern to eliminate pin holes. Application may be made by brush, roller or spray. Airless spray equipment or conventional heavy-duty spray equipment works well. ELASTO-TEX™ WALLCOATING HS is thixotropic rather than viscous and, therefore, breaks up easily in a spray pattern. The first coat must be thoroughly dry before applying a second coat. The time required will vary depending on temperature, wind and humidity. All ferrous surfaces should be primed with a rust inhibiting primer prior to application of ELASTO-TEX™ WALLCOATING HS. Equipment may be cleaned up with soap and water.

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-TEX™ PRIMER
ELASTO-TEX™ CAULK
ELASTO-TEX™ WALLCOATING HS

A VOC compliant, liquid-applied, two-component, polyurethane floor and wall coating for use in air fields, industrial plants, stores, and other locations where surfaces must withstand heavy use of foot traffic.
TECH DATA SHEET
AVAILABLE COLORS:

ELASTO-GLAZE™ CRU provides excellent resistance to UV light and abrasion and is a durable finish that protects floors against occasional chemical spillage, dirt, grease and oil. The product may be applied over epoxy floor systems to improve high-gloss retention and long-term wear resistance. ELASTO-GLAZE™ CRU may also be used as an anti-graffiti wall coating.

BASIC USES:
ELASTO-GLAZE™ CRU provides a reflective, bright appearance which will lighten up a warehouse by highlighting work areas and traffic lanes. Dusting of concrete floors is eliminated when the surface is sealed with ELASTO-GLAZE™ CRU and the floor is easily cleaned by detergent and water, as dirt and oils are prevented from penetrating the concrete. The cured product is easily cleaned with acetone.

ADVANTAGES:

• High Resistance to abrasion.
• Resistant to UV Light and yellowing.
• Easy to maintain.
• Hard but Flexible film.
• Convenient Volume Mixing Ratio of 1:1.
• Provides very good impact resistance.
• Good chemical resistance.
• Good against staining.
• Good weathering.
• Easy to clean with detergent and water.
• VOC Compliant (SCAQMD) 100gr/liter

CHEMICAL RESISTANCE:
ELASTO-GLAZE™ CRU resists most chemicals. After 7 days of contact at 77°F, testing of over 30 chemicals had no effect with the exception of some light staining in a few instances. Skydrol and Brake Fluid caused slight softening of the surface. The tests included most common solvents, acids used in chemical and food production, foodstuffs, common household and commercial cleaning fluids, alcohols, and oils. Note: all chemical spills should be cleaned up as soon as possible. Please review the Technical Data Sheet above for complete test results.

SURFACE PREPARATION:
All surfaces must be clean, sound and dry. Remove dust, grease, curing compounds, laitance, waxes, and other contaminants that may cause poor adhesion. All projections, rough spots, cracks, etc. should be dressed off to achieve a level surface prior to application. Surface should be sandblasted (or cleaned by other mechanical methods). Avoid acid etching if the coating is to be applied directly on the concrete. The surface must be dried prior to application to avoid any film defects. ELASTO-POXY™ PRIMER should be used if ELASTO-GLAZE™ CRU is used as dust-proofing sealer. All oxidation must be removed from metal surfaces and all metal surfaces must be primed with STAINLESS STEEL PRIMER.

APPLICATION:
ELASTO-GLAZE™ CRU may be applied by all conventional means including spray equipment, roller or brush. The recommended application rate of ELASTO-GLAZE™ CRU is two coats minimum, 200 to 250 sq. ft. per coat. Allow a minimum of 24 hours between coats. Allow light traffic after 72 hours and a minimum of 4 to 7 days for heavy traffic, to avoid any tire stains.

LIMITATIONS:
Containers that are opened must be used immediately. Avoid moisture contamination. ELASTO-GLAZE™ CRU should always be tested on all natural stones prior to any application to assure desired result. Protect all areas that are not to be coated such as glass, walls and plants from overspray and splashing. Remove material that has splashed on surface with acetone before material has dried. Material that is not removed immediately will be very difficult or impossible to remove. Condition the components to between 70°F and 85°F before using.

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-GLAZE™ CRU - COMPONENT-A
ELASTO-GLAZE™ CRU - COMPONENT-B

A single component, clear, moisture cured, polyurethane based coating, which provides a long lasting protective surface, when applied to plywood or other type wooden forms.
TECH DATA SHEET
AVAILABLE COLOR:

ELASTO-GLAZE™ FC is ideal for sealing un-oiled wood forms, which are used in forming concrete structures. The coating bonds extremely well to the wood surface protecting the forms from attack by the water and alkali in the fresh concrete poured against it. The cured film is tough, abrasion resistant and ready to receive a suitable form release agent prior to pouring concrete. This product is VOC compliant.

BENEFITS:

• Allows for multiple use of forms
• Fast dry
• Enhances concrete appearance
• Economical
• Prevents swelling of wood and transfer of grain marks to concrete product.

CHEMICAL RESISTANCE:

20% Detergent	No effect
50% Sodium Hydroxide	No effect
10% Sulfuric Acid	No effect
10% Hydrochloric Acid	No effect
5% Ammonia	No effect
20% Salt Solution	No effect
Anti-freezing Agent	No effect
Paint Thinner	No effect

SURFACE PREPARATION:
Surface must be clean, free of foreign material and sound. Surface should be dry. All cracks and defects should be repaired prior to coating with ELASTO-GLAZE™ FC. Light sanding is beneficial prior to application.

APPLICATION:
Apply by brush, spray, short nap roller or lambs wool applicator. Apply at approximately 300 sq.ft. per gallon per coat. Two coats are recommended for best results. NOTE: Material has a fast tack-free time. Keep a wet edge and DO NOT roll back into coating.

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-GLAZE™ FC

A premium acrylic base roof coating, reinforced with a polypropylene fabric, with an extended life expectancy for flat roofs and ponding.
TECH DATA SHEET | PRODUCT BULLETIN
AVAILABLE COLORS:

BASIC USES:
PREMIUM ELASTO-TEX™ ROOFCOAT is designed to be a highly durable, flexible roofcoating with outstanding resistance to weathering, ultra-violet light and water. Withstands ponding water conditions. It is suitable for application over sprayed urethane foam insulation roofs, concrete, wood or asphalt roofs. It serves as an excellent protection for urethane foam insulated storage tanks, grain elevators, etc.

BENEFITS AND SAVINGS

• CRRC Cool Roof Approved
• EnergyStar® Approved
• U.S. Green Building Council - Highest LEED™ Credits
• California Title 24 Compliant
• Top Tier Utility Rebates
• 100% Tax Deductible - 1st Year
• Durable in Extreme Weather, Resists Hail and High Winds
• Warranty - 5, 10, and 10 + 5 Year
• Renewable and Sustainable
• Save 30% of HVAC costs
• Safe - Cold Applied, No hot kettles
• No tear-off, No waste disposal

COATS OVER ANY EXISTING SUBSTRATE (*Please consult with a Pacific Polymers technical consultant for specific instructions and methods for each substrate.)

• Polyurethane Foam
• Concrete
• Asphalt
• Plywood
• Modified Bitumen
• Smooth Surface Emulsion
• Previously Coated Roofs
• BUR (Built-Up Roofs)
• Single-Ply
• Metal Roofs
• Corrugated Roofs

SURFACE PREPARATION:
All asphalt roofing must be clean and sound prior to application of PREMIUM ELASTO-TEX™ ROOFCOAT. Loose granules must be removed, blisters repaired, large cracks and voids caulked with an acrylic latex caulk, and the entire area washed with water and detergent. Rinse well and allow the roof to dry completely before applying the coating. Spray applied foam roofs must be coated within 48 hrs. in order to obtain good adhesion.

PRIMING:
Use Elasto-Tex™ Primer on concrete and previously coated surfaces, contingent on existing coating to be well adhered. Field testing is advised. Elasto-Tex™ Primer will greatly enhance adhesion to existing asphaltic roofing products, as well as wood and plywood. Metals must be protected with an anti rust primer, and allowed to dry according to manufacturer’s recommendations.

APPLICATION:

• Perimeter Detail: Install a cant strip at all internal corners using Elasto-Tex™ Caulk.
• Cracks & Seams: Apply a 6-inch strip of PREMIUM ELASTO-TEX™ ROOFCOAT and imbed Pac Poly Mat 101 seam tape into the wet material and cover with another coat.
• Base Coat: Apply PREMIUM ELASTO-TEX™ ROOFCOAT to the prepared area at a rate of 40 square feet per gallon and imbed Pac Poly Mat 101 re-inforcing fabric directly in the wet coating. Overlap adjacent runs of fabric by 4-5 inches. Make sure that no bubbles or wrinkles occur in the fabric.
• Intermediate Coat: Apply PREMIUM ELASTO-TEX™ ROOFCOAT at a rate of 45 square feet per gallon making sure to completely saturate the fabric.
• Top Coat: Apply PREMIUM ELASTO-TEX™ ROOFCOAT at a rate of 70 square feet per gallon.
• Recommended coverage over polyurethane foam roofs is 6 gallons per 100 square feet, old asphalt roofs may demand 6-8 gallons per 100 square feet. Always apply the coating in a minimum of three coats in a criss-cross pattern, in order to avoid pinholes. Allow 3-5 hours drying time in between coats..

MSDS DOCUMENTS FOR THIS SYSTEM:
PREMIUM ELASTO-TEX™ ROOFCOAT

Fluid applied heavy-duty waterproof traffic deck coating on concrete substrate. Wear-resistant polyurethane deck system that remains flexible even in extreme climates.
TECH DATA SHEET | CASE STUDY | CASE STUDY
MAINTENANCE MANUAL | APPLICATION GUIDE | PRODUCT BULLETIN
AVAILABLE COLORS:

ELASTO-DECK™ 5000 HT is a liquid-applied, single component, moisture-cured, seamless, slip resistant, polyurethane, waterproof deck coating. The system consists of ELASTO-DECK™ 5001HT BASE COAT and INTERMEDIATE COAT, and ELASTO-GLAZE™ 6001AL-HT TOP COAT, and a primer, where necessary.

BASIC USES:
For waterproofing parking decks and concrete roof decks. ELASTO-DECK™ 5000 HT can be used on all decks where a skid-resistant, long lasting, wear-resistant surface is required. It may be used on new decks as well as on existing concrete decks which are damaged or cracked. The system is suitable for exterior, as well as interior applications in all kinds of climates. The coating retains its elastomeric properties in below freezing weather, as well as in very hot climates.

APPLICATION:
A. Medium and heavy duty decks.
Step (1) ELASTO-DECK™ 5001 HT shall be applied to the primed concrete at a rate of 64 square feet per gallon (1.57 m²/liter) resulting in a film thickness of 25 mils (.63 cm). Application must be made uniformly to avoid thin spots and care must be taken to avoid pinholes and repair them should they occur.
Step (2) Following an overnight cure, apply ELASTO-DECK™ 5001 HT at a rate of 100 square feet per gallon (2.45 m²/liter) for a thickness of 16 mils (0.4 mm). It is preferable to use a heavy duty roller for even distribution.
Step (3) Immediately broadcast 1 gallon (3.785 liters) of 20 mesh Monterey sand, or equivalent, uniformly into the wet coating, per 100 sq.ft. (2.45 m²/liter). Assure that the coating is backrolled for even distribution of the sand. Do not broadcast to refusal. Allow to cure overnight.
*Step (4) Repeat Steps 2 and 3, where needed, as advised by the manufacturer. Allow an overnight cure of ELASTO-DECK™ 5001 HT. *For heavy-duty traffic areas.
Step (5) Apply ELASTO-GLAZE™ 6001AL-HT by roller, brush or spray at 150 sq.ft. per gallon (3.68 m²/liter) to equal 10 mils (0.25mm). Allow 72 hours for complete cure of the system.
Top coat must be the same color as the preceding sand coat.
B. Light duty pedestrian decks.
Step (1) As under A. Allow an overnight cure.
Step (2) Apply ELASTO-GLAZE™ 6001AL-HT at 100 square feet per gallon (2.45 m²/liter) or 16 (0.4mm) wet mils. Immediately broadcast 1 gallon of 20 mesh Monterey sand, or equivalent, uniformly into the wet coating, per 100 sq.ft (9.29 m²). Assure that the coating is backrolled for even distribution of the sand. Allow an overnight cure before permitting light traffic.

MATERIALS:
Recommended materials and their uses are as follows:
ELASTO-THANE™ 230 is a one part, self-leveling or gungrade, non-staining, polyurethane sealant which cures at ambient temperature to a firm, flexible tear-resistant rubber. It is highly resilient and has excellent recovery characteristics after extended periods of compression or elongation.
ELASTO-POXY™ PRIMER WB: A two-component, solvent based epoxy primer for use on concrete or metal surfaces.
ELASTO-DECK™ 5001 HT Coating: A one-part, self-leveling, polyurethane coating used as the elastomeric waterproof membrane of the system, and also to lock in the aggregate.
ELASTO-GLAZE™ 6001AL-HT Coating: A one-part, moisture-cured, aliphatic polyurethane topcoat which protects the ELASTO-DECK™ 5000 HT from U.V exposure.
AGGREGATE: 20 mesh Monterey sand or equal, which imparts the slip resistant texture and contributes to wear resistance.

MASTER SPECS:
SECTION 07181: (Word file)
TRAFFIC COATINGS ON PLYWOOD
SECTION 07182: (Word file)
TRAFFIC COATINGS ON CONCRETE
SECTION 07183: (Word file)
TRAFFIC COATINGS, HEAVY DUTY ON CONCRETE
SECTION 07570: (pdf)
TRAFFIC TOPPING

MSDS DOCUMENTS FOR THIS SYSTEM:
ELASTO-THANE™ 230
ELASTO-POXY™ PRIMER PART-A
ELASTO-POXY™ PRIMER PART-B
ELASTO-DECK™ 5001 HT
ELASTO-GLAZE™ 6001AL HT

CATALYSTS:

Super-Cure™ AL
Catalyst for: Cold Weather and/or Low Humidity
Accelerates the tack free time and cure time of:
2) Elasto-Glaze™ 6001ALHT
SUPER-CURE™ AL
SUPER-CURE™ AL

Super-Cure™ Rubber
Catalyst for: Cold Weather and/or Low Humidity
Accelerates the tack free time and cure time of:
3) Elasto-Deck™ 5001HT
SUPER-CURE™ RUBBER
SUPER-CURE™ RUBBER